openmediavault

The open network attached storage solution

News

  • New

    Hello I hope you can help.
    On my system runs OMV 4.1.13-1 with Docker 4.1 and Kernel 4.18.0-0

    When start OMV and I don't login in, comes following massage.

    Source Code

    1. [17280.218531] INFO: task md0_raid5:208 blocked for more than 120seconds.
    2. [17280.218612] Not tainted 4.18.0-0.bpo.1-amd64 #1 Debian 4.18.6-1~bpo9+1
    3. [17280.218681] "echo 0> /proc/sys/kernel/hung_task_timeout_secs" disables this message.
    4. [17280.218937] Info: task jbd2/md0-8:564 blocked for more than 120 seconds.
    5. and so on
    This message is only on the screen, in the log files I don't found this

    What means this message and how can isolve it? ?(
  • New

    Good afternoon, everyone,
    I have a question we currently have two locations. As far as I know it is possible to integrate several file systems into OMV. Now the question is: We have two locations file system A is at location A and file system B is at location B. Is there loadbalancing at OMV so that employees at location B can only access data from file system B?


    The problem is that the following large data must be available at each location. Now I have considered to transfer the data from file system A to B once at 0 o'clock at night. Depending on the location, the employees should then be able to access the next possible file system to have the fastest connection.

    Is such a thing possible with OMV if yes how would you realize it ? The connection between the locations is really very bad. That's why the synchronization between the locations is at 0 o'clock at night.

    Thank you in advance for replying
  • New

    Hello!,

    I didnt notice this "bug" but a couple of days ago, I tried to save some files to my share fodler. As usual, I logged in via SMB, everything ok, I created a folder and ok, but when I tried to save some files in this new Folder, I receive an error, that I dont have enough rights to save this file.

    As the title says, the last big change in this nas was the update from the version 2 to 3, after taht I didnt test if everything was ok. I didnt save anything until a couple of days, wich now is really anoying. Could somebody tell me what is wrong?

    Best regards.

    ML
  • OMV update OMV 4.x Resolved Update

    Kotera

    New

    Hello,
    I have problem with update. In GUI there is a lot of errors. When I login to ssh and run opt-update I got this:

    Source Code

    1. root@odroidc2:~# sudo omv-update
    2. Hit:1 http://packages.openmediavault.org/public arrakis InRelease
    3. Hit:3 http://security.debian.org stretch/updates InRelease
    4. Ign:2 http://cdn-fastly.deb.debian.org/debian stretch InRelease
    5. Hit:4 http://cdn-fastly.deb.debian.org/debian stretch-updates InRelease
    6. Hit:5 http://cdn-fastly.deb.debian.org/debian stretch-backports InRelease
    7. Hit:6 http://cdn-fastly.deb.debian.org/debian stretch Release
    8. Ign:7 https://dl.bintray.com/openmediavault-plugin-developers/arrakis stretch InRelease

Unread Threads

Topic Replies Last Reply

The Class E Network

437

flmaxey

Recovering from a drive failure

0

Cannot see file system after 2x to 4x upgrade! Disk is detected.

3

keribi560

Info message comes up when I don't login

0

OMV update

2

Kotera

Recent Activities

  • flmaxey -

    Replied to the thread The Class E Network.

    Post
    Quote from geaves: “TBH never heard of 'Catalytic' wood burners this site explains the functionality which by reading it improves the stoves efficiency, but the price on that site is a bit eye popping :) ” That's the genius behind the Englander design -…
  • geaves -

    Replied to the thread The Class E Network.

    Post
    Quote from flmaxey: “Well,, I simply looked at a map, but you followed the route! I know exactly what to do now - thanks for the tips. ” I was just pleased to get it sorted, there is one quirky thing which I can't get my head around you get an…
  • flmaxey -

    Replied to the thread The Class E Network.

    Post
    Well,, I simply looked at a map, but you followed the route! :) I know exactly what to do now - thanks for the tips. :thumbsup: Since we're talking about a near zero resources setup, I have an older B+ model I think I'll use for this. (The pi-hole folks say…
  • keribi560 -

    Replied to the thread OMV 4.x Cannot see file system after 2x to 4x upgrade! Disk is detected..

    Post
    I did forget to unmount the drives from the OMV 2xx before moving them to the OMV 4xx box,. I hope this is not a fatal mistake for the raid 5 array? It seems to have mounted in the OMV 4xx box fine. But OMV 4xx will not let me mount the single drive…
  • macom -

    Replied to the thread OMV 4.x Cannot see file system after 2x to 4x upgrade! Disk is detected..

    Post
    Search the forums for "wipefs" and you will find some threads dealing with this issue.
  • vandog -

    Posted the thread OMV 4.x Info message comes up when I don't login.

    Thread
    Hello I hope you can help. On my system runs OMV 4.1.13-1 with Docker 4.1 and Kernel 4.18.0-0 When start OMV and I don't login in, comes following massage. Source Code (6 lines)This message is only on the screen, in the log files I don't found…
  • Kotera -

    Replied to the thread OMV 4.x Resolved Update OMV update.

    Post
    Oh.. I found now that time on my device was so wrong. I changed it manually now, and everything is working perfect again. Thank you :)
  • martinmedia -

    Posted the thread OMV 4.x Data synchronization between file systems with OMV ?.

    Thread
    Good afternoon, everyone, I have a question we currently have two locations. As far as I know it is possible to integrate several file systems into OMV. Now the question is: We have two locations file system A is at location A and file system B is at…
  • geaves -

    Replied to the thread The Class E Network.

    Post
    Pi-Hole does work with DietPi :thumbsup: However, this will help you; Install OpenSSH from the dietpi-software menu by selecting the installed SSH, not the usual apt-get DietPi will boot using dhcp, but change this to static using dietpi-config -> do this
  • ryecoaaron -

    Replied to the thread OMV 3.x Lost rights after upgrade from OMV 2 to OMV 3.

    Post
    Upgrading to OMV3 changes the samba version. If you are trying to access via an old version of Windows, you might have this issue. What version of Windows are you using? Adding ntlm auth = yes to the extra options box in samba might fix it if you are…