Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • kiwijunglist -

    Replied to the thread OMV 4.x how to access / mount installation drive?.

    Post
    thank you. can i setup omv on my 500gb drive and then buy a small ssd, then migrate the whole system drive to another drive and use that as my system drive in the future?
  • gderf -

    Replied to the thread OMV 4.x how to access / mount installation drive?.

    Post
    OMV will not allow you to use the system drive for shared folders.
  • kiwijunglist -

    Posted the thread OMV 4.x how to access / mount installation drive?.

    Thread
    Hi I just installed OMV using the guide here: youtube.com/watch?time_continue=262&v=NYJCq2FwRUo I installed onto 500GB SSD and I have a 10x pre-populated ntfs HDDs. I'd like to setup shared folder on the SSD (OMV installation drive) for app data…
  • ryecoaaron -

    Replied to the thread OMV 4.x Headless, automated backup of the system SD-card on RPi.

    Post
    Quote from tkaiser: “correctly then the plugin creates an dd image only of the rootfs partition. If so this wouldn't be enough for the RPi since the main operating system (ThreadX) lives on the FAT32 boot partition. And without ThreadX no Linux/OMV…
  • flmaxey -

    Replied to the thread OMV 4.x No space left mergeFS.

    Post
    Well, I'm going to go out on the limb and say something is going on with /dev/sdd. :) Bad blocks - if we're talking about 1 or 2, maybe it's fixable for "awhile". Drives only last for so long. It may be time for a replacement.
  • DaveSk -

    Posted the thread OMV 4.x Partitaion starts at an offset of 3584 bytes.

    Thread
    HI folks, I'm completely new to OMV and debian Just trying to install to an external USB hard drive and when I select the disk, I get the error: The partition /dev/sda1 assigned to / starts at an offset of 3584 bytes from the minimum alignment of the…
  • tkaiser -

    Replied to the thread OMV 4.x Headless, automated backup of the system SD-card on RPi.

    Post
    Quote from badda: “So I guess, I'm not all wrong doing the backup my way ” Well, if I understood the restore procedure from @ryecoaaron correctly then the plugin creates an dd image only of the rootfs partition. If so this wouldn't be enough for the RPi…
  • ryecoaaron -

    Replied to the thread OMV 4.x How to save grub configuration..

    Post
    Quote from Spyrious: “sudo shellinaboxd -v -t -p 4200 --no-beep --linkify=none It is running. ” As it should, it is a daemon that isn't running in daemon mode. If it works that way, it should work when the service starts it. If it doesn't work, I…
  • ryecoaaron -

    Replied to the thread I cant share a port via Iptabless (Firewall).

    Post
    Quote from vbalazs: “How should I add port to the firewall rules? Please someone. ” You don't need to add anything to firewall rules. If you have anything, delete them. If port forwarding isn't working, then your router setup is wrong. What does…
  • bowe -

    Replied to the thread OMV 4.x No space left mergeFS.

    Post
    @flmaxey Thank you! But my nas would not start at all. Had it connected to a monitor and this happend imgur.com/aFZjRkq Running badblocks on that drive now, not sure if it will help or if I just should wipe it with dd zero. I don't have any important…
  • jollyrogr -

    Replied to the thread OMV 4.x how do u ping a hdd so it can be removed and i know which one to unplug.

    Post
    I thought it would be cool to use ledctl from the ledmon package but it doesn't work for me. Must not work with my HBA? serverfault.com/questions/6423…e-failed-hard-drive/64310 As it is, when I install a drive, I label it according to the slot it's…
  • flmaxey -

    Replied to the thread OMV 4.x how do u ping a hdd so it can be removed and i know which one to unplug.

    Post
    If the controller is integrated into the Mobo, I'd look for downloads on the Gigbyte site. Otherwise, if it's a card controller, I'd check to the maker of the controller for management software. I had an Adaptec controller that would "blink the light"…
  • geaves -

    Replied to the thread OMV 4.x How to save grub configuration..

    Post
    I'm sorry I'm at a loss, that's not creating the config file necessary, the last time I encountered something like this was during my first set up, so I just started again.
  • aniel -

    Replied to the thread OMV 4.x how do u ping a hdd so it can be removed and i know which one to unplug.

    Post
    yes i mean blink the drive light, as for the management software where do i find that since i do have and using the sas controller. my mob is: b2b.gigabyte.com/Server-Motherboard/GA-7TESM-rev-10#sp
  • aniel -

    Posted the thread OMV 4.x mergerfs hdd removal question.

    Thread
    when you remove a hdd out of the mergerfs pool does it move all files/ folders in that hdd to the other hdds ?
  • flmaxey -

    Replied to the thread OMV 4.x how do u ping a hdd so it can be removed and i know which one to unplug.

    Post
    If you have a sas controller, management software for the controller might do it (if you mean blink the drive light). In OMV, under storage Physical Disks, you'll find the HD model number and serial number, matched to the device name /dev/sd?. Drive…
  • omarius -

    Posted the thread Crashing.

    Thread
    Hi, i'm running OMV on my rock64 (2gb) variant, with the propper psu, a 16gb microsd class 10. I currently use it as a Nas & a plex media server, but it keeps crashing every other day, and that is without using it as a plex server, I have a rpi running…
  • samukets -

    Replied to the thread OMV 4.x Resolved Sonarr Permission Issue.

    Post
    Solved, the problem was in mapping the folders, even the transmission creating the complete subfolder, we should not point it in the docker. Before: / sharedfolders / downloads / complete / ... / downloads After: / sharedfolders / downloads / ... /…
  • aniel -

    Posted the thread OMV 4.x how do u ping a hdd so it can be removed and i know which one to unplug.

    Thread
    i have a supermicro 3u case with hot swappable hdd bays and i would like to know if is is possible to ping a hdd in omv so i can know which one to unplug and replaced, etc, thank you
  • Spyrious -

    Replied to the thread OMV 4.x How to save grub configuration..

    Post
    Done everything,but when I hit apply I get this Failed to execute command 'export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin; export LANG=C.UTF-8; omv-mkconf shellinabox 2>&1' with exit code '2':…