Search Results

Search results 1-20 of 197.

  • balancing out my hard drive space

    majorpayne - - General

    Post

    Quote from gderf: “Was it related to mergerfs? ” Yes, Using UFS with Mergerfs

  • balancing out my hard drive space

    majorpayne - - General

    Post

    Afternoon, When i first loaded my media onto my Hard drives I used the wrong method for balancing out the files. I have learn from that mistake since then, While i was searching for something else I ran across software that would help me rebalance the files. the issue is I thought I made a bookmark but alas I did not. Can anyone help me relocate that software?

  • Now to figure out my unrar cron command again that i lost when i reformatted. Thanks for the assist

  • Let me check into that. I have never seen that option before.

  • Found the mistake I forgot to add >>

  • I did the following Source Code (1 line) Then updated Source Code (1 line) tried to install using and it stil failed. Source Code (1 line)

  • looks like it's available just not installed? so just apt-get install par2 unrar root@openmediavault:~# apt-get install par2 unrar Reading package lists... Done Building dependency tree Reading state information... Done Package unrar is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'unrar' has no installation candidate root@openmediavault:~#

  • I'm looking to see if the instructions are still correct for OMV 4.0, if something need to be change please let me know. Do i need to replace Jessie and wheezy to strech? Backup your sources.list file cp /etc/apt/sources.list /etc/apt/sources.list.bak Add a source to the sources.list echo deb ftp.us.debian.org/debian/ jessie main >> /etc/apt/sources.list Add another source echo deb ftp.us.debian.org/debian/ wheezy non-free >> /etc/apt/sources.list Update your package lists apt-get update Install…

  • I'd a retard, For some reason the whole bloody problem was where i was saving the config folder. It couldn't access the location. Does anyone know where the config files are stored in a docker container

  • Hey all, My plex took a crap and I decided I would just start over and install OMV 4.0, then Load Plex running on Docker. I set it up following Installation and Setup Videos - Beginning, Intermediate and Advanced and followed each step minus a couple of differences. When I attempt to go to the plex webpage i get a This site can’t be reached 192.168.0.15 refused to connect in chrome. in IE Can’t reach this page Make sure the web address 192.168.0.15:33400 is correct. What am I missing. I have att…

  • Firewall question

    majorpayne - - General

    Post

    Quote from geaves: “Quote from majorpayne: “this look right? ” If this was Docker you would just add the ports, depending on how it was installed I don't use Plex, but according to what I've found you have to open ports on the machine plex is on as this is for internal use. Have you installed the webtools and tried to connect?...That would be my first start. Re your images, you should specify a source and destination, in other words ip of where the request is coming from, and it's destination, w…

  • Firewall question

    majorpayne - - General

    Post

    this look right?

  • Firewall question

    majorpayne - - General

    Post

    Quote from geaves: “You only have to open the ports on the computer Plex is running on. ” Ok, that is what i was asking, it's wierd that i have never opened any other ports on the OMV server and other things are working just fine.

  • Firewall question

    majorpayne - - General

    Post

    Good Morning, I'm attempting to install Webtools for plex (non docker) and I was wondering if I need to open up the ports 33400 and 33443 as the instructions say or does the firewall in this case not matter. I have never opened any ports on any of the other items I have install which of course might be error on my part. I know that although I have use OMV for many years I'm still what I consider a noob as I do not play with it much since it just works.

  • Has anyone run any type of software? I'm trying to find something good for my SCCM, Powershell and VBS scripts.

  • PFsense question

    majorpayne - - General

    Post

    well then, I guess that answers that question. Thank you.

  • PFsense question

    majorpayne - - General

    Post

    *** I'm not knowledgeable about pfsense in any way shape or form. *** I was wondering if integrating pfSense into OMV was a plausible possibility as a option. what if any are the complications or would get in the way...

  • Help: RAID 5 data Recovery

    majorpayne - - General

    Post

    Quote from ade86: “ Any ideas on how to rebuild this raid 5 partition to accept the two 'replacement' drives? thanks -Adrian ” Unfortunately, to my knowledge, a Raid 5 only allows the loss of 1 drive. Raid 6 allows the loss of 2 drives.

  • Upgrading Hard Disks

    majorpayne - - General

    Post

    Quote from BFLK: “Hello, Please describe your setup (number of drives / capacity / raid configuration) now, and the one that you are aiming after the upgrade. In this moment, the information that you provided in insufficient and I can't answer your question accurately. ” I'm currently running a Lenovo Tiny m900 with a i7-6700T, I have 2 4 Bay Mediasonic Proboxe's connected via USB3.0 Each Device has a assortment of drive sizes ranging from 2TB - 4TB in them. I'm currently running a Raid 5 for ea…

  • Upgrading Hard Disks

    majorpayne - - General

    Post

    Quote from BFLK: “Hello, From my point of view, the only safe way to upgrade is to use another machine to create the new MD array, transfer the data, then move the array to the original system. The procedure that you pinpointed above is correct, but it doesn't take into consideration the fact that you need to perform one rebuild after each HDD is replaced, and the chance for an unrecoverable read error to occur is not negligible. I tell you this because on one from 3xWD RED 3TB (WD30EFRX) I star…