That's very interesting, it's similar but it doesn't sound exactly the same as the problem I'm seeing. These failed transfers don't cause any long-term problem for the connectivity, pings and such work immediately after the failed transfers. Furthermore, the transfers fail immediately, rather than after a large amount of data has already transferred. Even a small file such as omv-extras plugin can't even initiate the download on wget.
Well, mostly. The NIC appears to be just incompatible with Linux. Not a deal breaker, I'll leave my USB NIC plugged in, which is an easy enough workaround.
However, I got all four drives recognized!
For anyone else who is ever trying to get Linux, FreeBSD, or any other operating system that isn't Windows booting on their HP Mediasmart EX470 or EX475, here is the procedure:
Using a USB keyboard, after power on as soon as the health LED begins to blink blue and red hit DELETE and it'll become solid (either blue or red depending on what it was when you hit delete) and enter the BIOS. Advice on the Internet suggests to wait 5 seconds after this to ensure it's in the BIOS. Press F10 and then ENTER to save and reboot. Repeat this process until you're fully comfortable with the process of blindly booting into the BIOS and safely saving and exiting.
Boot into the BIOS again.
Press the DOWN arrow three (3) times to reach Integrated Peripherals
Press ENTER to select
Press the DOWN arrow one (1) time to select SIS OnChip PCI Device
Press ENTER to select
Press the DOWN arrow eight (8) times to select SIS Serial ATA Mode
Press PGDN one (1) time to select 4P(IDE)+4S(IDE).
Press F10 one (1) time to save and exit.
Press ENTER to confirm.
I figured this out by studying this video:
In that post, he lists out all the modes:
4P(IDE)+4S(RAID) => 4 Sata Ports in Raid Mode (Driver required, hotswap supported)
4P(IDE)+4S(IDE) => 4 Sata Ports in IDE Emulation Mode (No Driver required)
2P2S(IDE)+2S(RAID) => 2 'IDE' Sata Ports, 2 'RAID' Sata Ports *
2P2S(IDE)+2S(AHCI) => 2 'IDE' Sata Ports, 2 'AHCI' Sata Ports *
4P(IDE)+2S(RAID) => 2 'RAID' Sata Ports
4P(IDE)+2S(AHCI) => 2 'AHCI' Sata Ports
From other web searches, I saw that the top one, 4P(IDE)+4S(RAID), is the default.
Applies to HP EX470 - EX475 (and potentially others.)
I built OMV on another AMD 64bit box, using a USB drive. I used the disk change in BIOS, as noted above (thanks to @creamsicle for that info.), to go strictly to JBOD and set BIOS to boot from USB.
I got the onboard NIC to work by using a CN2 to VGA cable (custom made), to connect a monitor, and running omv-firstaid after the first boot. To get a DHCP address, it was necessary to do a hard power reset, as in unplug it. (Unfortunately, the EX470 will only do a soft reset with the switch.) After that, the NIC got an address.
Good backup takes the "drama" out of computing
Primary: OMV 3.0.99, ThinkServer TS140, 12GB ECC, 32GB USB boot, 4TB+4TB zmirror, 3TB client backup.
Backup: OMV 4.1.9, Acer RC-111, 4GB, 32GB USB boot, 3TB+3TB zmirror, 4TB Rsync'ed disk
2nd Data Backup: OMV 3.0.99, R-PI 2B, 16GB boot, 4TB WD USB MyPassport - direct connect (no hub)
The post was edited 3 times, last by flmaxey: edit2 ().