Hello.
I own banana pi with 3.5 HDD, and yesterday i copied lots of data (circa 100GB) to HDD. After 30min i noticed something goes wrong, copying canceled, and i did not see shared folders, so i rebooted my banana pi , but it dont boot up. . So i disconnected sata cables and finaly banana pi booted up. So i connected back the HDD and in setting(Physical disks tab) i can see HDD, but if i click to mount HDD (File systems tab) it says:
Failed to mount '1c2a87e9-0efc-4ce0-81fb-854bcf2289d1': [mntent]: warning: no final newline at the end of /etc/fstab mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so
so i tryied dmesg(part of dmesg):
[ 3.139963] I2C: i2c-4: HDMI I2C adapter
[ 3.717781] [mmc-msg] mmc 0 detect change, present 1
[ 4.226813] [mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.238232] [mmc-msg] sdc0 power on
[ 4.267237] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.281550] [mmc-msg] sdc0 set round clock 400000, src 24000000
[ 4.364523] [mmc-err] smc 0 err, cmd 52, RTO
[ 4.373019] [mmc-err] smc 0 err, cmd 52, RTO
[ 4.385732] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.405856] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.420617] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.428929] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.437241] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.445556] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.458810] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.476556] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.496675] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.582285] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.600034] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.614675] [mmc-msg] sdc0 set round clock 42857143, src 600000000
[ 4.689344] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[ 4.703320] mmc0: new high speed SDHC card at address aaaa
[ 4.712702] mmcblk0: mmc0:aaaa SU08G 7.40 GiB
[ 4.720338] mmcblk0: p1 p2
[ 13.171846] Timeout waiting for EDID info
[ 13.182238] disp clks: lcd 74250000 pre_scale 1 hdmi 74250000 pll 297000000 2x 0
[ 13.732641] Console: switching to colour frame buffer device 160x45
[ 13.765392] axp20_buck3: incomplete constraints, leaving on
[ 13.776005] axp20_buck2: incomplete constraints, leaving on
[ 13.786499] axp20_ldo4: incomplete constraints, leaving on
[ 13.796906] axp20_ldo3: incomplete constraints, leaving on
[ 13.807308] axp20_ldo2: incomplete constraints, leaving on
[ 13.817710] axp20_ldo1: incomplete constraints, leaving on
[ 13.826369] console [netcon0] enabled
[ 13.833678] netconsole: network logging started
[ 13.842534] otg_wakelock_init: No USB transceiver found
[ 13.855461] sunxi-rtc sunxi-rtc: setting system clock to 2015-11-07 21:33:55 UTC (1446932035)
[ 13.871864] ALSA device list:
[ 13.883735] #0: sunxi-CODEC Audio Codec
[ 13.899670] md: Waiting for all devices to be available before autodetect
[ 13.917021] md: If you don't use raid, use raid=noautodetect
[ 13.939007] md: Autodetecting RAID arrays.
[ 13.952224] md: Scanned 0 and added 0 devices.
[ 13.964094] md: autorun ...
[ 13.974839] md: ... autorun DONE.
[ 14.004292] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
[ 14.027835] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[ 14.046569] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 14.069762] devtmpfs: mounted
[ 14.081759] Freeing init memory: 224K
[ 14.983741] udevd[161]: starting version 175
[ 15.892575] ata1.00: configured for UDMA/133
[ 15.904650] ata1: EH complete
[ 15.946970] ata1.00: configured for UDMA/133
[ 15.959042] ata1: EH complete
[ 16.599765] ata1.00: configured for UDMA/133
[ 16.611732] ata1: EH complete
[ 16.689897] ata1.00: configured for UDMA/133
[ 16.701913] ata1: EH complete
[ 18.373435] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 18.629599] 8021q: 802.1Q VLAN Support v1.8
[ 21.269838] Adding 524284k swap on /swapfile1. Priority:-1 extents:6 across:745468k SS
[ 22.271457] EXT4-fs error (device mmcblk0p2): ext4_mb_generate_buddy:741: group 17, 7559 clusters in bitmap, 7708 in gd
[ 22.414078] ADDRCONF(NETDEV_UP): lo: link is not ready
[ 24.453071] GMAC gpio_power_hd:gpio_direction_output
[ 24.723858] eth0: device MAC address 02:56:07:c2:d5:15
[ 24.753353] sunxi_gmac: probed
[ 24.768097] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active
[ 24.785580] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01)
[ 26.854796] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 29.792101] PHY: sunxi_gmac-0:00 - Link is Up - 1000/Full
[ 41.539024] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 249.975201] ata1: hard resetting link
[ 250.332575] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 250.355130] ata1.00: configured for UDMA/133
[ 250.361525] ata1: EH complete
[ 307.605467] ata1: hard resetting link
[ 307.954825] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 307.977388] ata1.00: configured for UDMA/133
[ 307.983818] ata1: EH complete
[ 314.114831] EXT4-fs (mmcblk0p2): error count since last fsck: 5
[ 314.128300] EXT4-fs (mmcblk0p2): initial error at time 1446823037: ext4_mb_generate_buddy:741
[ 314.144332] EXT4-fs (mmcblk0p2): last error at time 1446932043: ext4_mb_generate_buddy:741
[ 464.953498] ata1: hard resetting link
[ 465.311011] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 465.333857] ata1.00: configured for UDMA/133
[ 465.340488] ata1: EH complete
[ 1236.682330] ata1: hard resetting link
[ 1237.041228] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1237.064053] ata1.00: configured for UDMA/133
[ 1237.070563] ata1: EH complete
[86811.098972] EXT4-fs (mmcblk0p2): error count since last fsck: 5
[86811.112503] EXT4-fs (mmcblk0p2): initial error at time 1446823037: ext4_mb_generate_buddy:741
[86811.128634] EXT4-fs (mmcblk0p2): last error at time 1446932043: ext4_mb_generate_buddy:741
[119869.649684] EXT4-fs (sda1): ext4_check_descriptors: Checksum for group 4144 failed (36262!=0)
[119869.663033] EXT4-fs (sda1): group descriptors corrupted!
[120544.200579] EXT4-fs (sda1): ext4_check_descriptors: Checksum for group 4144 failed (36262!=0)
[120544.213426] EXT4-fs (sda1): group descriptors corrupted!
[120735.862541] ata1: hard resetting link
[120736.225211] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[120736.252293] ata1.00: configured for UDMA/133
[120736.263562] ata1: EH complete
[120746.817835] EXT4-fs (sda1): ext4_check_descriptors: Checksum for group 4144 failed (36262!=0)
[120746.835463] EXT4-fs (sda1): group descriptors corrupted!
[121140.251152] EXT4-fs (sda1): ext4_check_descriptors: Checksum for group 4144 failed (36262!=0)
[121140.272176] EXT4-fs (sda1): group descriptors corrupted!
[121666.179486] EXT4-fs (sda1): ext4_check_descriptors: Checksum for group 4144 failed (36262!=0)
[121666.199566] EXT4-fs (sda1): group descriptors corrupted!
Alles anzeigen
and here is my /etc/fstab:
# UNCONFIGURED FSTAB FOR BASE SYSTEM
# 512 MB swapfile
/swapfile1 swap swap defaults 0 0
tmpfs /tmp tmpfs defaults 0 0
# >>> [openmediavault]
UUID=1c2a87e9-0efc-4ce0-81fb-854bcf2289d1 /media/1c2a87e9-0efc-4ce0-81fb-854bcf2289d1 ext4 defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,acl 0 2
# <<< [openmediavault]
I'm a beginner in linux things, so i need your help to repair this problem