SMART "Passed", OMV says drive status "Bad"

    • OMV 2.x
    • SMART "Passed", OMV says drive status "Bad"

      Brand new to OMV. Fresh install on all brand new hardware and I have a drive showing as bad. The SMART info says it passed though.



      SMART data:

      === START OF READ SMART DATA SECTION ===
      SMART overall-health self-assessment test result: PASSED

      SMART Attributes Data Structure revision number: 16
      Vendor Specific SMART Attributes with Thresholds:
      ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
      1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1
      3 Spin_Up_Time POS--K 100 253 021 - 0
      4 Start_Stop_Count -O--CK 100 100 000 - 3
      5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
      7 Seek_Error_Rate -OSR-K 100 253 000 - 0
      9 Power_On_Hours -O--CK 100 100 000 - 2
      10 Spin_Retry_Count -O--CK 100 253 000 - 0
      11 Calibration_Retry_Count -O--CK 100 253 000 - 0
      12 Power_Cycle_Count -O--CK 100 100 000 - 2
      192 Power-Off_Retract_Count -O--CK 200 200 000 - 1
      193 Load_Cycle_Count -O--CK 200 200 000 - 0
      194 Temperature_Celsius -O---K 123 116 000 - 27
      196 Reallocated_Event_Count -O--CK 200 200 000 - 0
      197 Current_Pending_Sector -O--CK 200 200 000 - 1
      198 Offline_Uncorrectable ----CK 100 253 000 - 0
      199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
      200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
      ||||||_ K auto-keep
      |||||__ C event count
      ||||___ R error rate
      |||____ S speed/performance
      ||_____ O updated online
      |______ P prefailure warning
    • SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
      Device Error Count: 13
      CR = Command Register
      FEATR = Features Register
      COUNT = Count (was: Sector Count) Register
      LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
      LH = LBA High (was: Cylinder High) Register ] LBA
      LM = LBA Mid (was: Cylinder Low) Register ] Register
      LL = LBA Low (was: Sector Number) Register ]
      DV = Device (was: Device/Head) Register
      DC = Device Control Register
      ER = Error register
      ST = Status register
      Powered_Up_Time is measured from power on, and printed as
      DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
      SS=sec, and sss=millisec. It "wraps" after 49.710 days.

      Error 13 [12] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:56:04.234 SMART READ LOG
      b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 02:56:04.234 SMART READ LOG
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:56:04.234 SMART READ LOG
      60 04 00 00 80 00 00 9a 21 82 a0 40 08 02:56:04.164 READ FPDMA QUEUED
      60 04 00 00 78 00 00 9a 21 7e a0 40 08 02:56:04.164 READ FPDMA QUEUED

      Error 12 [11] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:49:53.145 SMART READ LOG
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:49:53.145 SMART READ LOG
      60 04 00 00 c8 00 00 94 ec 03 38 40 08 02:49:53.078 READ FPDMA QUEUED
      60 04 00 00 c0 00 00 94 eb ff 38 40 08 02:49:53.078 READ FPDMA QUEUED
      60 04 00 00 b8 00 00 94 eb fb 38 40 08 02:49:53.078 READ FPDMA QUEUED

      Error 11 [10] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:39:19.292 SMART READ LOG
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:39:19.292 SMART READ LOG
      60 04 00 00 28 00 00 8b ea fb 38 40 08 02:39:19.216 READ FPDMA QUEUED
      60 04 00 00 20 00 00 8b ea f7 38 40 08 02:39:19.216 READ FPDMA QUEUED
      60 04 00 00 18 00 00 8b ea f3 38 40 08 02:39:19.216 READ FPDMA QUEUED

      Error 10 [9] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:37:20.637 SMART READ LOG
      60 04 00 00 a8 00 00 8a 38 5b 38 40 08 02:37:20.562 READ FPDMA QUEUED
      60 04 00 00 a0 00 00 8a 38 57 38 40 08 02:37:20.562 READ FPDMA QUEUED
      60 04 00 00 98 00 00 8a 38 53 38 40 08 02:37:20.562 READ FPDMA QUEUED
      60 04 00 00 90 00 00 8a 38 4f 38 40 08 02:37:20.562 READ FPDMA QUEUED

      Error 9 [8] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:00:23.541 SMART READ LOG
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 02:00:23.541 SMART READ LOG
      60 02 20 00 70 00 00 6a 14 bc 40 40 08 02:00:23.456 READ FPDMA QUEUED
      60 04 00 00 68 00 00 6a 14 b8 40 40 08 02:00:23.456 READ FPDMA QUEUED
      60 04 00 00 60 00 00 6a 14 b4 40 40 08 02:00:23.456 READ FPDMA QUEUED

      Error 8 [7] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 01:58:53.165 SMART READ LOG
      60 03 68 00 e0 00 00 68 b8 36 60 40 08 01:58:53.120 READ FPDMA QUEUED
      60 04 00 00 d8 00 00 68 b8 32 60 40 08 01:58:53.120 READ FPDMA QUEUED
      60 04 00 00 d0 00 00 68 b8 2e 60 40 08 01:58:53.120 READ FPDMA QUEUED
      60 04 00 00 c8 00 00 68 b8 2a 60 40 08 01:58:53.120 READ FPDMA QUEUED

      Error 7 [6] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 01:50:16.776 SMART READ LOG
      60 01 a0 00 28 00 00 60 df 92 60 40 08 01:50:16.729 READ FPDMA QUEUED
      60 04 00 00 20 00 00 60 df 8e 60 40 08 01:50:16.729 READ FPDMA QUEUED
      60 04 00 00 18 00 00 60 df 8a 60 40 08 01:50:16.729 READ FPDMA QUEUED
      60 04 00 00 10 00 00 60 df 86 60 40 08 01:50:16.729 READ FPDMA QUEUED

      Error 6 [5] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
      When the command that caused the error occurred, the device was active or idle.

      After command completion occurred, registers were:
      ER -- ST COUNT LBA_48 LH LM LL DV DC
      -- -- -- == -- == == == -- -- -- -- --
      04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT

      Commands leading to the command that caused the error were:
      CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 01:49:42.193 SMART READ LOG
      b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 01:49:42.193 SMART READ LOG
      60 03 68 00 e0 00 00 60 58 32 f8 40 08 01:49:42.129 READ FPDMA QUEUED
      60 04 00 00 d8 00 00 60 58 2e f8 40 08 01:49:42.129 READ FPDMA QUEUED
      60 04 00 00 d0 00 00 60 58 2a f8 40 08 01:49:42.129 READ FPDMA QUEUED
    • This is because of:

      197 Current_Pending_Sector -O--CK 200 200 000 - 1

      Current Pending Sector Count S.M.A.R.T. parameter is a critical parameter and indicates the current count of unstable sectors (waiting for remapping). The raw value of this attribute indicates the total number of sectors waiting for remapping. Later, when some of these sectors are read successfully, the value is decreased. If errors still occur when reading some sector, the hard drive will try to restore the data, transfer it to the reserved disk area (spare area) and mark this sector as remapped.

      kb.acronis.com/content/9133
    • I also have a "bad" drive:

      forum.openmediavault.org/index…9f755af52d7b584eae72878c2

      seems due to Available_Reserved_Space and Media_Wearout_Indicator.
      After 5000 h of utilization and total host writes of 4,2 TB, I am neither going to scrap it nor to make a RMA.

      To me the indicator is false positive.
      To check this, I passed this to Chrystal Disk Info, which said: Good(99%).
      Images
      • 2016-02-20 21_39_58-openmediavault web administration interface - HP-OMV.local.png

        24.64 kB, 660×343, viewed 359 times