Fresh installation of OMV4, unable to mount old XFS drive, with data, that works on OMV2

    • OMV 4.x (stable)

    This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

    • Fresh installation of OMV4, unable to mount old XFS drive, with data, that works on OMV2

      Hello there,
      I do need a helping hand / guidance.
      I have a single 3TB drive with old data, XFS filesystem, and OMV4 on a USB stick (and another stick with OMV2).
      Under OMV4, I am able to see the 3TB disk under Disks, as sda, BUT this is not visible/available under Filesystems, so I am unable to mount it. I am able to create, but this will wipe out my disk/data. If I plug another disk/usb drive, I am able to mount it under Filesystems, but sda is still invisible.
      If I use OMV2, it's all ok, I am able to see/use the 3TB drive.
      I should be able to use putty so, perhaps a magical mount command will fix my issue on OMV4, if anyone will be able to assist me with this, please.
      I did a search in forum, with no luck. Additional data, I believe I formatted the drive with OMV1, xfs filesystem, 4 years ago.

      Thanks in advance!
      Daniel
    • Hi Tkaiser,

      Thanks for your quick reply.

      Here is the output:
      ==================================

      Linux Haspeu 4.13.0-0.bpo.1-amd64 #1 SMP Debian 4.13.13-1~bpo9+1 (2017-11-22) x86_64


      The programs included with the Debian GNU/Linux system are free software;
      the exact distribution terms for each program are described in the
      individual files in /usr/share/doc/*/copyright.


      Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
      permitted by applicable law.


      root@Haspeu:~# uname -a
      Linux Haspeu 4.13.0-0.bpo.1-amd64 #1 SMP Debian 4.13.13-1~bpo9+1 (2017-11-22) x86_64 GNU/Linux
      root@Haspeu:~# lsblk -a
      NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
      sda 8:0 0 2.7T 0 disk
      ââsda1 8:1 0 2.7T 0 part
      sdb 8:16 1 7.5G 0 disk
      ââsdb1 8:17 1 5.5G 0 part /
      ââsdb2 8:18 1 1K 0 part
      ââsdb5 8:21 1 2G 0 part [SWAP]
      root@Haspeu:~# blkid
      /dev/sdb1: UUID="8eacee61-ba53-415c-bba3-e3f5c2690793" TYPE="ext4" PARTUUID="d0e792a8-01"
      /dev/sdb5: UUID="2f1b59d1-6752-4ede-8912-b5d17d01c42a" TYPE="swap" PARTUUID="d0e792a8-05"
      root@Haspeu:~# smartctl -a /dev/sda
      smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.13.0-0.bpo.1-amd64] (local build)
      Copyright (C) 2002-16, Bruce Allen, Christian Franke, smartmontools.org


      === START OF INFORMATION SECTION ===
      Model Family: Western Digital Red
      Device Model: WDC WD30EFRX-68AX9N0
      Firmware Version: 80.00A80
      User Capacity: 3,000,592,982,016 bytes [3.00 TB]
      Sector Sizes: 512 bytes logical, 4096 bytes physical
      Device is: In smartctl database [for details use: -P show]
      ATA Version is: ACS-2 (minor revision not indicated)
      SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
      SMART support is: Available - device has SMART capability.
      SMART support is: Enabled


      === START OF READ SMART DATA SECTION ===
      SMART overall-health self-assessment test result: PASSED


      General SMART Values:
      Offline data collection status: (0x00) Offline data collection activity
      was never started.
      Auto Offline Data Collection: Disabled.
      Self-test execution status: ( 0) The previous self-test routine completed
      without error or no self-test has ever
      been run.
      Total time to complete Offline
      data collection: (39240) seconds.
      Offline data collection
      capabilities: (0x7b) SMART execute Offline immediate.
      Auto Offline data collection on/off support.
      Suspend Offline collection upon new
      command.
      Offline surface scan supported.
      Self-test supported.
      Conveyance Self-test supported.
      Selective Self-test supported.
      SMART capabilities: (0x0003) Saves SMART data before entering
      power-saving mode.
      Supports SMART auto save timer.
      Error logging capability: (0x01) Error logging supported.
      General Purpose Logging supported.
      Short self-test routine
      recommended polling time: ( 2) minutes.
      Extended self-test routine
      recommended polling time: ( 394) minutes.
      Conveyance self-test routine
      recommended polling time: ( 5) minutes.
      SCT capabilities: (0x70bd) SCT Status supported.
      SCT Error Recovery Control supported.
      SCT Feature Control supported.
      SCT Data Table supported.


      SMART Attributes Data Structure revision number: 16
      Vendor Specific SMART Attributes with Thresholds:
      ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
      1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
      3 Spin_Up_Time 0x0027 181 178 021 Pre-fail Always - 5916
      4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 586
      5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
      7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
      9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 712
      10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
      11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
      12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 470
      192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 43
      193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 542
      194 Temperature_Celsius 0x0022 125 114 000 Old_age Always - 25
      196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
      197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
      198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
      199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
      200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0


      SMART Error Log Version: 1
      ATA Error Count: 1
      CR = Command Register [HEX]
      FR = Features Register [HEX]
      SC = Sector Count Register [HEX]
      SN = Sector Number Register [HEX]
      CL = Cylinder Low Register [HEX]
      CH = Cylinder High Register [HEX]
      DH = Device/Head Register [HEX]
      DC = Device Command Register [HEX]
      ER = Error register [HEX]
      ST = Status register [HEX]
      Powered_Up_Time is measured from power on, and printed as
      DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
      SS=sec, and sss=millisec. It "wraps" after 49.710 days.


      Error 1 occurred at disk power-on lifetime: 202 hours (8 days + 10 hours)
      When the command that caused the error occurred, the device was active or idle.


      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      04 51 01 00 00 00 00 Error: ABRT


      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
      -- -- -- -- -- -- -- -- ---------------- --------------------
      b0 d5 01 e1 4f c2 00 08 01:04:18.163 SMART READ LOG
      b0 d6 01 e0 4f c2 00 08 01:04:18.163 SMART WRITE LOG
      b0 d6 01 e0 4f c2 00 08 01:04:18.161 SMART WRITE LOG
      b0 d5 01 e0 4f c2 00 08 01:04:18.161 SMART READ LOG


      SMART Self-test log structure revision number 1
      Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
      # 1 Short offline Completed without error 00% 203 -
      # 2 Short offline Aborted by host 30% 203 -
      # 3 Short offline Aborted by host 90% 203 -
      # 4 Short offline Completed without error 00% 202 -
      # 5 Short offline Aborted by host 90% 202 -


      SMART Selective self-test log data structure revision number 1
      SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
      1 0 0 Not_testing
      2 0 0 Not_testing
      3 0 0 Not_testing
      4 0 0 Not_testing
      5 0 0 Not_testing
      Selective self-test flags (0x0):
      After scanning selected spans, do NOT read-scan remainder of disk.
      If Selective self-test is pending on power-up, resume after 0 minute delay.


      root@Haspeu:~#
      ============================================================

      I am attaching a screenshot from OMV4 File System Menu, so you may see that sda1 is not visible, although it exists, so I am unable to mount it, using the GUI.

      Thank you for your time!

      Regards,
      Daniel