10GB Mellanox (MCX353A-QCBT) OMV3 OFED

  • Helllo



    I have Test System HP N54L I'm would like to gt it setup with

    Mellanox ConnectX-3 CX353A



    Using SSH


    Code
    LSPCI
    02:00.0 Network controller: Mellanox Technologies MT27500 Family [ConnectX-3]







    Code
    uname -r
    4.9.0-0.bpo.4-amd64



    Code
    cat /etc/debian_version
    8.9


    So I head to the mellanox site and download


    MLNX_OFED_LINUX-4.3-1.0.1.0-debian8.9-x86_64.tgz


    unpack the folder

    Code
    tar zxvf


    According to Mellanox
    cd to the directory and then


    Code
    ./mlnxofedinstall


    This is when I get stuck when I run the above command the message displays


    Current operation system in not supported!


    There is an option I'm not sure about this so i'd though I ask if it's ok to try this.


    .

    Code
    /mlnxofedinstall --add-kernel-support


    Thanks

    3 Mal editiert, zuletzt von RacerX () aus folgendem Grund: Mistake

  • Maybe u could use code-tags and link to all the stuff you mentioned?
    Its very hard to read and understand...

    --
    Get a Rose Tattoo...


    HP t5740 with Expansion and USB3, Inateck Case w/ 3TB WD-Green
    OMV 5.5.23-1 Usul i386|4.19.0-9-686-pae

  • There is an option I'm not sure about this so i'd though I ask if it's ok to try this.


    I read your post twice. I looked for what you are asking. Did you ask a question? What is it you are wanting from this community?

    Version7.0-32 (Sandworm)
    ProcessorAMD EPYC 7302P 16-Core Processor
    KernelLinux 6.1.15-1-pve
    HardwareDell R7515
  • Hello


    I made progress with Ubuntu 16.04 . Basically in order to run the mellanox OFED install script I need the kernel sources or I need to change the install not to check the OS. Unbuntu 16.04 has the kernel sources in



    Code
    /usr/src

    I haven't used debian for a long time so can I get the kernel sources with something like apt-get install ???



    Thanks

  • When I setup the card in Ubuntu it flashed the firmware on my card, So Nnw when I boot OMV3 the card is present inbios and to the installer. When I run OMV-FirstAid the card shows up in the list of network cards. Super.....


    Thanks

    • Offizieller Beitrag

    When I setup the card in Ubuntu it flashed the firmware on my card

    Ubuntu loads firmware for the card but should never make a permanent change to the card like flashing firmware on the card.

    omv 7.0.4-2 sandworm | 64 bit | 6.5 proxmox kernel

    plugins :: omvextrasorg 7.0 | kvm 7.0.10 | compose 7.1.2 | k8s 7.0-6 | cputemp 7.0 | mergerfs 7.0.3


    omv-extras.org plugins source code and issue tracker - github


    Please try ctrl-shift-R and read this before posting a question.

    Please put your OMV system details in your signature.
    Please don't PM for support... Too many PMs!

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!