OMV system Standby via UI trigger not working

    • OMV 4.x

    This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

    • OMV UI Standby not working

      Hello,

      i have done a new installation of OMV on my NAS system (own build, configuration see below) but if i use the Standby function from UI the UI is switching view to xxx.xxx.xxx.xxx\shutdown.php and i see a blue screen with a red button in my browser. But my NAS seems to do nothing and it is still accessable and using the same power. If i enter the direct command "systemctl suspend" my NAS is switching into suspend to ram mode with a power consumention of 3-4 kwh. Some updates ago if i pressed the "Standy" button on the UI, it happend the same as i entered the command. Can anyone help?

      Hardware:
      CPU: Intel Core I3-8300
      Mainboard: ASROCK B360 Pro4
      RAM: Kingston 8 GB ValueRAM Single Rank DDR4-2400 DIMM CL17-17-17 Single
      Data drives: 2x 128GB Intel 600p M.2 2280 PCIe 3.0 x4 (1x System, 1x Docker/VMs)
      3x 10000GB Seagate IronWolf ST10000VN0004 (SnapRaid)
      power: 300 Watt LC-Power LC420-12 Non-Modular 80+ Bronze

      Software:
      OMV: 4.18.2-1
      Linux Kernel: 4.16.0-0.bpo.2-amd64

      Installed Plugins
      - anacron (not in use)
      - apttool (not in use)
      - autoshutdown
      - backup (inactive)
      - clamav (inactive)
      - distkstats
      - docker-gui
      - downloader (not in use)
      - flashmemory
      - letsencrypt
      - luksencryption (not in use)
      - lvm (not in use)
      - minidlna (inactive)
      - omvextrasorg
      - remotedesktop
      - remotemount (inactive)
      - resetperms
      - shellinabox
      - snapraid
      - symlinks
      - teamviewerhost
      - unionfilesystems
      - usbbackup (inactive)
      - virtualbox (inactive)
      - wakealarm (inactive)
      - webdav (inactive)
      - WOL

      Installed Docker containers:
      - Plex media server


      Additional:
      - configured smb shares
      - WOL configured IP + MAC addresses
      - configured notifications
    • OMV uses the pm-hibernate, pm-powersave, pm-suspend-hybrid, pm-is-supported and pm-suspend CLI tools to manage the power management. Maybe they work different than systemctl. The internal scripts use pm-is-supported to check which power mode is supported, so i assume that this does not really work well on your system.
      Absolutely no support through PM!

      I must not fear.
      Fear is the mind-killer.
      Fear is the little-death that brings total obliteration.
      I will face my fear.
      I will permit it to pass over me and through me.
      And when it has gone past I will turn the inner eye to see its path.
      Where the fear has gone there will be nothing.
      Only I will remain.

      Litany against fear by Bene Gesserit
    • Power management is tricky. Maybe a new kernel has broken something.
      Absolutely no support through PM!

      I must not fear.
      Fear is the mind-killer.
      Fear is the little-death that brings total obliteration.
      I will face my fear.
      I will permit it to pass over me and through me.
      And when it has gone past I will turn the inner eye to see its path.
      Where the fear has gone there will be nothing.
      Only I will remain.

      Litany against fear by Bene Gesserit
    • New

      Ok, i found the problem. I have installed the Flash memory plugin.
      Install instructions:
      1. Execute the following command: nano /etc/fstab
      2. Add noatime and nodiratime to root options. See before and after example lines:
        BEFORE:UUID=ccd327d4-a1ed-4fd2-b356-3b492c6f6c34 / ext4 errors=remount-ro 0 1AFTER:UUID=ccd327d4-a1ed-4fd2-b356-3b492c6f6c34 / ext4 noatime,nodiratime,errors=remount-ro 0 1
      3. Comment out the swap partition. See before and after example lines (only need to add a # to beginning of the line):
        BEFORE:UUID=a3c989d8-e12b-41d3-b021-098155d6b21b none swap sw 0 0AFTER:#UUID=a3c989d8-e12b-41d3-b021-098155d6b21b none swap sw 0 0
        If i just change the line mentioned in point 2, standby is working, but if i also change the line mentioned in point 3 (deactivating the swap partition) standby is not working anymore. Does anyone know this bug or have any idea how i can solve this?
    • New

      m1l0 wrote:

      Ok, i found the problem. I have installed the Flash memory plugin.
      That is why these instructions are optional. Personally, i would not use standby with an SD card since you are going to be doing a lot of writes every time you go into standby.
      omv 4.1.8.2 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.8
      omv-extras.org plugins source code and issue tracker - github.com/OpenMediaVault-Plugin-Developers

      Please read this before posting a question.
      Please don't PM for support... Too many PMs!
    • Users Online 1

      1 Guest