getting error during installation of OMV

    This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

    • getting error during installation of OMV

      hi,
      I followed the guide : Install OMV4 on Debian 9 (Stretch)

      and I am getting the attached error :

      this is my sys details:
      Raspberry Pi 3 Model B Rev 1.2

      PRETTY_NAME="Raspbian GNU/Linux 9 (stretch)"
      NAME="Raspbian GNU/Linux"
      VERSION_ID="9"
      VERSION="9 (stretch)"
      ID=raspbian
      ID_LIKE=debian
      HOME_URL="http://www.raspbian.org/"
      SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
      BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"
      Files
      • error.txt

        (51.89 kB, downloaded 18 times, last: )
    • Seems to be a problem with the Debian package named 'resolvconf'. Make sure it is installed. I'm wondering why it is not installed because it is listed in the openmediavault package dependency.
      Absolutely no support through PM!

      I must not fear.
      Fear is the mind-killer.
      Fear is the little-death that brings total obliteration.
      I will face my fear.
      I will permit it to pass over me and through me.
      And when it has gone past I will turn the inner eye to see its path.
      Where the fear has gone there will be nothing.
      Only I will remain.

      Litany against fear by Bene Gesserit
    • zaki wrote:

      and I am getting the attached error :
      Why not use the image? sourceforge.net/projects/openm…/Raspberry%20Pi%20images/

      The RPi is a pain and you are much better off to use the image.
      omv 4.1.13 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!
    • I tried to use the image but for some reason I cannot see the web gui,
      once typing the ip displayed during the installation, I was getting "page cannot be reached" and check proxy configuration.

      once pinging that Ip, I do get results.

      so I tried other way- it looks both have issues on my pi
    • zaki wrote:

      I tried to use the image but for some reason I cannot see the web gui,
      once typing the ip displayed during the installation, I was getting "page cannot be reached" and check proxy configuration.
      Are you waiting 30+ mins for the image to be ready? Does the rpi have an internet connection when the image is getting ready?
      omv 4.1.13 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!
    • hi, I tried once more, and same issue - meaning it was asking me to enter the user name and password after 20 seconds, and then he prompting again to insert the user name and password over and over again, then i waited for more then 30 min - hoping something will change, but it isnt.

      for the ssh user/password did not work, it says "access denied"
    • zaki wrote:

      meaning it was asking me to enter the user name and password after 20 seconds, and then he prompting again to insert the user name and password over and over again, then i waited for more then 30 min - hoping something will change, but it isnt.

      for the ssh user/password did not work, it says "access denied"
      You need to write the image with etcher, put the card in the rpi, plug it in, and walk away for 30+ mins. Don't try to configure anything. After that, try to login to the web interface to add a user with ssh access or enable root access via ssh.
      omv 4.1.13 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!
    • sorry for late response (had some issues to recover my password), but did the exact steps mentioned. waited for whole night and same no results.
      i am adding few images of the console during the startup.

      thanks in advanced.
      Images
      • IMG_20180912_234939.jpg

        672.6 kB, 1,732×2,309, viewed 33 times
      • IMG_20180912_235019.jpg

        592.54 kB, 1,732×2,309, viewed 27 times
      • IMG_20180913_051732.jpg

        583.02 kB, 1,732×2,309, viewed 34 times
      • IMG_20180913_051735.jpg

        665.85 kB, 1,732×2,309, viewed 29 times
      • IMG_20180913_051740.jpg

        696.84 kB, 1,732×2,309, viewed 34 times
    • zaki wrote:

      sorry for late response (had some issues to recover my password), but did the exact steps mentioned. waited for whole night and same no results.
      i am adding few images of the console during the startup.
      I don't see anything really wrong other than maybe an nfs issue. You tried going to http://192.168.31.207 in a browser? If that doesn't work, either something is wrong with your network or engined isn't running. You should be able to login as root (password is openmediavault) and take a pic of the output of: systemctl status openmediavault-engined and systemctl status nginx
      omv 4.1.13 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!