Fresh installation and : "systemctl maintenance"

    • OMV 4.x
    • Update
    • Fresh installation and : "systemctl maintenance"

      Hi :D



      I have a problem with my fresh arrakis installation !


      When I reboot, arrakis say I'm on maintenance mode and I can see log or continu booting. So i continu booting and all start "normaly" exept my raid volume doesn't mount ! I have to mount it on the GUI.



      Have you got any idees to fix my issue ?

      Thx :
    • Your raid array isn't assembling correctly for some unknown reason. This why it stops at the maintenance prompt. If you don't fix your array, it will keep doing this.
      omv 4.1.17 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!
    • Hi !


      After boot and manualy mount my raid, I go on the GUI I can see the raid statut and the statut is "clean".
      The detail :

      Source Code

      1. Version : 1.2
      2. Creation Time : Wed Aug 23 23:14:03 2017
      3. Raid Level : raid5
      4. Array Size : 11720540160 (11177.58 GiB 12001.83 GB)
      5. Used Dev Size : 2930135040 (2794.39 GiB 3000.46 GB)
      6. Raid Devices : 5
      7. Total Devices : 5
      8. Persistence : Superblock is persistent
      9. Intent Bitmap : Internal
      10. Update Time : Fri Dec 7 20:39:33 2018
      11. State : clean
      12. Active Devices : 5
      13. Working Devices : 5
      14. Failed Devices : 0
      15. Spare Devices : 0
      16. Layout : left-symmetric
      17. Chunk Size : 512K
      18. Name : OMV56:0 (local to host OMV56)
      19. UUID : c171d3c7:c92ffaf5:887bf054:3c9c693e
      20. Events : 100773
      21. Number Major Minor RaidDevice State
      22. 0 8 0 0 active sync /dev/sda
      23. 1 8 16 1 active sync /dev/sdb
      24. 2 8 32 2 active sync /dev/sdc
      25. 3 8 48 3 active sync /dev/sdd
      26. 5 8 80 4 active sync /dev/sdf
      Display All
      How can I check the raid area ?


      THX
    • rantanplan wrote:

      How can I check the raid area ?
      The array is clean. Maybe it isn't assembling fast enough during boot? Are these usb drives and/or is this an RPi?

      I would run omv-mkconf mdadm as root to see if it helps.
      omv 4.1.17 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!
    • Your array still isn't assembling in time. Hard to say why. Look through boot logs to see if something is obvious. This is one of the reasons why I think most people shouldn't use raid.
      omv 4.1.17 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!
    • Okay, I run
      systemctl list-units --failed :


      UNIT LOAD ACTIVE SUB DESCRIPTION


      ● mdmonitor.service loaded failed failed MD array monitor
      ● systemd-fsck@dev-disk-by\x2dlabel-Data.service loaded failed failed File System Check on /dev/disk/by-label/Data


      LOAD = Reflects whether the unit definition was properly loaded.
      ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
      SUB = The low-level unit activation state, values depend on unit type.


      2 loaded units listed. Pass --all to see loaded but inactive units, too.
      To show all installed unit files use 'systemctl list-unit-files'.


      Do you think it's a clue ?
    • rantanplan wrote:

      Do you think it's a clue ?
      No. Both of those probably failed because your array isn't assembling.
      omv 4.1.17 arrakis | 64 bit | 4.15 proxmox kernel | omvextrasorg 4.1.13
      omv-extras.org plugins source code and issue tracker - github

      Please read this before posting a question and this and this for docker questions.
      Please don't PM for support... Too many PMs!