Problems with netatalk during update to 1.0

    • Problems with netatalk during update to 1.0

      Hello,

      I got the following error during the upgrade:

      Source Code

      1. Errors were encountered while processing:
      2. netatalk
      3. openmediavault-netatalk
      4. Creating index of upgradeable packages ...
      5. Creating index of OpenMediaVault plugins ...
      6. E: Sub-process /usr/bin/dpkg returned an error code (1)


      So should i remove netatalk via apt-get and install it later again?

      Thankks for your help....
      OMV 4 Arrakis | Kernel 4.14 ... running on
      SelfBuilt NAS -- Asrock Q1900-ITX -- 4x 2,4 GHz in Burst Mode -- 4 GB DDR3 RAM -- RAID 5 -- 3x 3TB WD Red
    • OK i solved this problem, seems to be a problem in the script if netatalk is running, just had to stop it and it worked after it.

      Now the omv-release-upgrade is not there anymore.
      How can i bring the update to an end?
      OMV 4 Arrakis | Kernel 4.14 ... running on
      SelfBuilt NAS -- Asrock Q1900-ITX -- 4x 2,4 GHz in Burst Mode -- 4 GB DDR3 RAM -- RAID 5 -- 3x 3TB WD Red
    • omv-release-upgrade isn´t there anymore


      Yes the command gets removed after the upgrade. If the above commands didn't show any errors and just lines like:

      Source Code

      1. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
      Then the upgrade finished.
      You can also check your omv version via the webui.
    • I had the same problem while upgrading from a Beta 0.6 version to OMV 1.0.

      I purge-removed netatalk and reinstalled again.

      apt-get --purge remove openmediavault-netatalk
      then reboot, then
      apt-get install openmediavault-netatalk
      OMV stoneburner | HP Microserver | 256GB Samsung 830 SSD for system | 4x 2TB in a RAID5
      OMV erasmus| Odroid XU4 | 5TB Data drive | 500GB Backup drive
    • OK, everything working now without problems but the performance is terrible.

      normaly my nas reads with 115 mb/s and writes with 80 mb/s with protocol afp.
      Now read speed is maybe a bit slower but not much..... But write speed is terrible (2 - 3 mb/s ...... after some time normal speed for a few seconds....)

      I tried to check the network performance with iperf.... read and write is about 117 mb/s .... so the network is not the problem....
      Also tried disk speed .... write tested via dd is about 100 mb/s .... read speed tested via hdparm is about 150 mb/s.
      So everything should be fine.....

      Also tried to write over smb instead of afp to see whats the problem, but the terrible write speed is the same......

      Strange thing.....

      Do you have a idea?


      Edit: Also tried to write via ftp and the problem is also the same.....
      OMV 4 Arrakis | Kernel 4.14 ... running on
      SelfBuilt NAS -- Asrock Q1900-ITX -- 4x 2,4 GHz in Burst Mode -- 4 GB DDR3 RAM -- RAID 5 -- 3x 3TB WD Red
    • Backports made it a little bit better but still terrible.

      One interessting thing:
      If i use iperf to during the copy process, it get´s much faster as long as iperf stresses the networkcard.

      Maybe a p state governor problem?

      Somebody else have a idea?

      Edit:
      Found this in dmesg:


      [ 2.889818] microcode: CPU0 sig=0x30673, pf=0x4, revision=0x321

      [ 2.893289] platform microcode: firmware: agent aborted loading intel-ucode/06-37-03 (not found?)

      [ 2.893421] microcode: CPU1 sig=0x30673, pf=0x4, revision=0x321

      [ 2.896776] platform microcode: firmware: agent aborted loading intel-ucode/06-37-03 (not found?)

      [ 2.896924] microcode: CPU2 sig=0x30673, pf=0x4, revision=0x321

      [ 2.900354] platform microcode: firmware: agent aborted loading intel-ucode/06-37-03 (not found?)

      [ 2.900503] microcode: CPU3 sig=0x30673, pf=0x4, revision=0x321

      [ 2.903793] platform microcode: firmware: agent aborted loading intel-ucode/06-37-03 (not found?)

      [ 2.904007] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba

      OMV 4 Arrakis | Kernel 4.14 ... running on
      SelfBuilt NAS -- Asrock Q1900-ITX -- 4x 2,4 GHz in Burst Mode -- 4 GB DDR3 RAM -- RAID 5 -- 3x 3TB WD Red

      The post was edited 1 time, last by wastez ().

    • There are different governors for p states (ondemand, conservative) and for c states (menu, ladder). Its a Celeron itx quad core j1900. (pretty new)
      Already tried to stress the CPU, also helps a Little Bit but not as much as the LAN stress.
      Hope i find a Solution otherwise i have to go back to 0.5.


      OMV 4 Arrakis | Kernel 4.14 ... running on
      SelfBuilt NAS -- Asrock Q1900-ITX -- 4x 2,4 GHz in Burst Mode -- 4 GB DDR3 RAM -- RAID 5 -- 3x 3TB WD Red