SMART Error ABRT increasing ATA error count

    • OMV 1.0
    • Resolved

    This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

    • SMART Error ABRT increasing ATA error count

      My ATA error count on two drives keep increasing due to what I believe is an ABRT Error. I have pasted the SMART Logs for the drive bellow. Should I start to be worried about this or is it something I can ignore for now?

      Brainfuck Source Code

      1. SMART Attributes Data Structure revision number: 16
      2. Vendor Specific SMART Attributes with Thresholds:
      3. ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
      4. 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
      5. 3 Spin_Up_Time POS--K 140 140 021 - 15000
      6. 4 Start_Stop_Count -O--CK 100 100 000 - 10
      7. 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
      8. 7 Seek_Error_Rate -OSR-K 200 200 000 - 0
      9. 9 Power_On_Hours -O--CK 100 100 000 - 91
      10. 10 Spin_Retry_Count -O--CK 100 253 000 - 0
      11. 11 Calibration_Retry_Count -O--CK 100 253 000 - 0
      12. 12 Power_Cycle_Count -O--CK 100 100 000 - 10
      13. 192 Power-Off_Retract_Count -O--CK 200 200 000 - 6
      14. 193 Load_Cycle_Count -O--CK 200 200 000 - 50
      15. 194 Temperature_Celsius -O---K 095 091 000 - 57
      16. 196 Reallocated_Event_Count -O--CK 200 200 000 - 0
      17. 197 Current_Pending_Sector -O--CK 200 200 000 - 0
      18. 198 Offline_Uncorrectable ----CK 200 200 000 - 0
      19. 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
      20. 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1
      21. ||||||_ K auto-keep
      22. |||||__ C event count
      23. ||||___ R error rate
      24. |||____ S speed/performance
      25. ||_____ O updated online
      26. |______ P prefailure warning
      27. After command completion occurred, registers were:
      28. ER -- ST COUNT LBA_48 LH LM LL DV DC
      29. -- -- -- == -- == == == -- -- -- -- --
      30. 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
      31. Commands leading to the command that caused the error were:
      32. CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      33. -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      34. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+23:45:53.762 SMART READ LOG
      35. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+23:45:53.762 SMART READ LOG
      36. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+23:45:53.762 SMART READ LOG
      37. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+23:45:53.761 SMART WRITE LOG
      38. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+23:45:53.761 SMART READ LOG
      39. Error 4 [3] occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
      40. When the command that caused the error occurred, the device was active or idle.
      41. After command completion occurred, registers were:
      42. ER -- ST COUNT LBA_48 LH LM LL DV DC
      43. -- -- -- == -- == == == -- -- -- -- --
      44. 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
      45. Commands leading to the command that caused the error were:
      46. CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      47. -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      48. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+22:09:19.796 SMART READ LOG
      49. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.796 SMART WRITE LOG
      50. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.796 SMART WRITE LOG
      51. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.795 SMART READ LOG
      52. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.795 SMART READ LOG
      53. Error 3 [2] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours)
      54. When the command that caused the error occurred, the device was active or idle.
      55. After command completion occurred, registers were:
      56. ER -- ST COUNT LBA_48 LH LM LL DV DC
      57. -- -- -- == -- == == == -- -- -- -- --
      58. 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
      59. Commands leading to the command that caused the error were:
      60. CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      61. -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      62. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 10:43:56.886 SMART READ LOG
      63. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 10:43:56.886 SMART READ LOG
      64. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 10:43:56.885 SMART WRITE LOG
      65. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 10:43:56.885 SMART WRITE LOG
      66. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 10:43:56.885 SMART READ LOG
      67. Error 2 [1] occurred at disk power-on lifetime: 43 hours (1 days + 19 hours)
      68. When the command that caused the error occurred, the device was active or idle.
      69. After command completion occurred, registers were:
      70. ER -- ST COUNT LBA_48 LH LM LL DV DC
      71. -- -- -- == -- == == == -- -- -- -- --
      72. 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
      73. Commands leading to the command that caused the error were:
      74. CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      75. -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      76. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:18:17.086 SMART READ LOG
      77. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:18:17.086 SMART READ LOG
      78. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:18:17.086 SMART WRITE LOG
      79. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:18:17.085 SMART WRITE LOG
      80. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:18:17.085 SMART READ LOG
      81. Error 1 [0] occurred at disk power-on lifetime: 37 hours (1 days + 13 hours)
      82. When the command that caused the error occurred, the device was active or idle.
      83. After command completion occurred, registers were:
      84. ER -- ST COUNT LBA_48 LH LM LL DV DC
      85. -- -- -- == -- == == == -- -- -- -- --
      86. 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
      87. Commands leading to the command that caused the error were:
      88. CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
      89. -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
      90. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:53:34.333 SMART READ LOG
      91. b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:53:34.333 SMART READ LOG
      92. b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:53:34.332 SMART READ LOG
      93. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:53:34.331 SMART WRITE LOG
      94. b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:53:34.331 SMART WRITE LOG
      95. SMART Extended Self-test Log Version: 1 (1 sectors)
      96. No self-tests have been logged. [To run self-tests, use: smartctl -t]
      97. SMART Selective self-test log data structure revision number 1
      98. SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
      99. 1 0 0 Not_testing
      100. 2 0 0 Not_testing
      101. 3 0 0 Not_testing
      102. 4 0 0 Not_testing
      103. 5 0 0 Not_testing
      104. Selective self-test flags (0x0):
      105. After scanning selected spans, do NOT read-scan remainder of disk.
      106. If Selective self-test is pending on power-up, resume after 0 minute delay.
      107. SCT Status Version: 3
      108. SCT Version (vendor specific): 258 (0x0102)
      109. SCT Support Level: 1
      110. Device State: Active (0)
      111. Current Temperature: 57 Celsius
      112. Power Cycle Min/Max Temperature: 27/61 Celsius
      113. Lifetime Min/Max Temperature: 27/61 Celsius
      114. Under/Over Temperature Limit Count: 0/139
      115. SCT Temperature History Version: 2
      116. Temperature Sampling Period: 1 minute
      117. Temperature Logging Interval: 1 minute
      118. Min/Max recommended Temperature: 0/60 Celsius
      119. Min/Max Temperature Limit: -41/85 Celsius
      120. Temperature History Size (Index): 478 (455)
      121. Index Estimated Time Temperature Celsius
      122. 456 2014-09-29 18:58 57 **************************************
      123. ... ..(476 skipped). .. **************************************
      124. 455 2014-09-30 02:55 57 **************************************
      125. SCT Error Recovery Control:
      126. Read: Disabled
      127. Write: Disabled
      128. SATA Phy Event Counters (GP Log 0x11)
      129. ID Size Value Description
      130. 0x0001 2 0 Command failed due to ICRC error
      131. 0x0002 2 0 R_ERR response for data FIS
      132. 0x0003 2 0 R_ERR response for device-to-host data FIS
      133. 0x0004 2 0 R_ERR response for host-to-device data FIS
      134. 0x0005 2 0 R_ERR response for non-data FIS
      135. 0x0006 2 0 R_ERR response for device-to-host non-data FIS
      136. 0x0007 2 0 R_ERR response for host-to-device non-data FIS
      137. 0x0008 2 0 Device-to-host non-data FIS retries
      138. 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
      139. 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
      140. 0x000b 2 0 CRC errors within host-to-device FIS
      141. 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
      142. 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
      143. 0x8000 4 171928 Vendor specific
      Display All
      ASUS P9A-I/C2550/SAS/4L w/ Intel Atom C2550 (2.40GHz) | Kingston ECC 16GB RAM | 1x 120GB OS HDD| 8x 2TB HDD (RAID 6) | SilverStone DS380
      OMV 2.1.23 Stone Burner (64 bit) | Debian 7 (Wheezy) w/Kernel 3.2.0-4-amd64
    • djrbx wrote:

      194 Temperature_Celsius -O---K 095 091 000 - 57


      djrbx wrote:

      Current Temperature: 57 Celsius
      Power Cycle Min/Max Temperature: 27/61 Celsius
      Lifetime Min/Max Temperature: 27/61 Celsius


      djrbx wrote:

      Under/Over Temperature Limit Count: 0/139


      Those quotes should answer your question... your environment is too hot for your hard drives.

      Greetings
      David
      "Well... lately this forum has become support for everything except omv" [...] "And is like someone is banning Google from their browsers"

      Only two things are infinite, the universe and human stupidity, and I'm not sure about the former.


      Upload Logfile via WebGUI/CLI
      #openmediavault on freenode IRC | German & English | GMT+1
      Absolutely no Support via PM!

      I host parts of the omv-extras.org Repository, the OpenMediaVault Live Demo and the pre-built PXE Images. If you want you can take part and help covering the costs by having a look at my profile page.