Constant WebGUI timeout errors

    • OMV 1.0

    This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

    • Constant WebGUI timeout errors

      Clean install of OMV, and have since done a full update. Both before and after update, I get constant timeout errors in the webgui making it nigh-on impossible to get anything done. I've searched around but no threads I found had problems matching mine.

      Screenshot in first attachment: ignore the fact this is in the mhddfs plugin, it happens all over in native areas on the gui too.
      Not sure if it's relevant but when attempting to load something that causes the timeout the gui is also a bit wonky, as per second attachment.

      nginx error logs are full of this:

      Source Code

      1. 2014/12/04 18:12:26 [error] 32487#0: *4998 upstream timed out (110: Connection timed out) while reading response header from upstream, client: ::ffff:10.0.0.113, server: openmediavault-webgui, request: "POST /rpc.php HTTP/1.1", upstream: "fastcgi://unix:/var/run/php5-fpm-openmediavault-webgui.sock:", host: "10.0.0.100", referrer: "http://10.0.0.100/"


      Tried to increase fastcgi timeout (fastcgi_read_timeout 120s;) but made no difference; errors appear before timeout anyway, sometimes within a few seconds.

      It's not a particularly powerful box (intentional for low power consumption) but never had these issues on 0.x which I'd been running for about a year. Would like to avoid re-building from scratch, but I've got nowhere in reconfiguring my setup so can do so if needs be. I have installed omvextras and mhddfs but due to problems encountered have not yet configured. Have only SSH service running, nothing else.

      Also tried this from another thread, made no difference

      Source Code

      1. sudo /etc/init.d/openmediavault-engined restart


      Some support info

      Brainfuck Source Code

      1. top - 19:01:00 up 2 days, 19:41, 2 users, load average: 0.00, 0.07, 0.40
      2. Tasks: 104 total, 1 running, 103 sleeping, 0 stopped, 0 zombie
      3. %Cpu(s): 0.5 us, 0.4 sy, 0.0 ni, 98.0 id, 1.1 wa, 0.0 hi, 0.0 si, 0.0 st
      4. KiB Mem: 3094692 total, 1827928 used, 1266764 free, 66152 buffers
      5. KiB Swap: 134140 total, 0 used, 134140 free, 1607560 cached
      6. ================================================================================
      7. = OS/Debian information
      8. ================================================================================
      9. Distributor ID: debian
      10. Description: Debian GNU/Linux 7 (wheezy)
      11. Release: 7.7
      12. Codename: wheezy
      13. ================================================================================
      14. = OpenMediaVault information
      15. ================================================================================
      16. Release: 1.4
      17. Codename: Kralizec
      18. ================================================================================
      19. = Date
      20. ================================================================================
      21. Thu Dec 4 18:58:27 PST 2014
      22. ================================================================================
      23. = Locale
      24. ================================================================================
      25. en_CA.UTF-8
      26. ================================================================================
      27. = System information
      28. ================================================================================
      29. Linux nas 3.2.0-4-amd64 #1 SMP Debian 3.2.60-1+deb7u3 x86_64 GNU/Linux
      30. Processor: Intel Atom CPU 230 @ 1.6GHz in Dell Optiplex FX160, 4GB RAM
      31. ================================================================================
      32. = Uptime
      33. ================================================================================
      34. 18:58:27 up 2 days, 19:39, 2 users, load average: 0.00, 0.08, 0.44
      35. ================================================================================
      36. = Network interfaces
      37. ================================================================================
      38. 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
      39. link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
      40. inet 127.0.0.1/8 scope host lo
      41. inet6 ::1/128 scope host
      42. valid_lft forever preferred_lft forever
      43. 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
      44. link/ether 00:1f:16:fa:6a:8d brd ff:ff:ff:ff:ff:ff
      45. inet 10.0.0.100/24 brd 10.0.0.255 scope global eth0
      46. --------------------------------------------------------------------------------
      47. Interface information eth0:
      48. ===========================
      49. Settings for eth0:
      50. Supported ports: [ TP ]
      51. Supported link modes: 10baseT/Half 10baseT/Full
      52. 100baseT/Half 100baseT/Full
      53. 1000baseT/Half 1000baseT/Full
      54. Supported pause frame use: No
      55. Supports auto-negotiation: Yes
      56. Advertised link modes: 10baseT/Half 10baseT/Full
      57. 100baseT/Half 100baseT/Full
      58. 1000baseT/Half 1000baseT/Full
      59. Advertised pause frame use: Symmetric
      60. Advertised auto-negotiation: Yes
      61. Speed: 1000Mb/s
      62. Duplex: Full
      63. Port: Twisted Pair
      64. PHYAD: 1
      65. Transceiver: internal
      66. Auto-negotiation: on
      67. MDI-X: Unknown
      68. Supports Wake-on: g
      69. Wake-on: g
      70. Current message level: 0x000000ff (255)
      71. drv probe link timer ifdown ifup rx_err tx_err
      72. Link detected: yes
      73. --------------------------------------------------------------------------------
      74. Driver information eth0:
      75. ========================
      76. driver: tg3
      77. version: 3.121
      78. firmware-version: 5764m-v3.35
      79. bus-info: 0000:02:00.0
      80. supports-statistics: yes
      81. supports-test: yes
      82. supports-eeprom-access: yes
      83. supports-register-dump: yes
      84. supports-priv-flags: no
      85. ================================================================================
      86. = IP routing table
      87. ================================================================================
      88. Kernel IP routing table
      89. Destination Gateway Genmask Flags Metric Ref Use Iface
      90. 0.0.0.0 10.0.0.1 0.0.0.0 UG 0 0 0 eth0
      91. 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
      92. ================================================================================
      93. = Linux Software RAID
      94. ================================================================================
      95. Not used
      Display All



      Thanks for any pointers.
      Images
      • Screen Shot 2014-12-04 at 6.44.19 PM.png

        53.36 kB, 527×426, viewed 347 times
      • Screen Shot 2014-12-04 at 6.39.04 PM.png

        56.24 kB, 616×424, viewed 358 times

      The post was edited 1 time, last by Hwulex ().

    • Same thing now running update to plugins, and also trying to add a Shared Folder.
      Images
      • Screen Shot 2014-12-04 at 7.12.48 PM.png

        105.51 kB, 1,006×529, viewed 324 times
      • Screen Shot 2014-12-04 at 7.18.42 PM.png

        14.53 kB, 405×260, viewed 339 times

      The post was edited 1 time, last by Hwulex ().

    • Transfer speeds and ping are fine, if not blistering. Transferring between MBP2008+MtnLion and FX160+OMV over WiFi via LinksysE3200+ddwrt.

      Source Code

      1. dom@mbp ~/Movies $ scp video.mp4 nas:~/
      2. video.mp4 100% 258MB 9.2MB/s 00:28


      Source Code

      1. dom@mbp ~/ $ ping nas
      2. PING nas.ds.net (10.0.0.100): 56 data bytes
      3. 64 bytes from 10.0.0.100: icmp_seq=0 ttl=64 time=1.810 ms
      4. 64 bytes from 10.0.0.100: icmp_seq=1 ttl=64 time=1.057 ms
      5. 64 bytes from 10.0.0.100: icmp_seq=2 ttl=64 time=1.226 ms
      6. 64 bytes from 10.0.0.100: icmp_seq=3 ttl=64 time=1.032 ms
      7. 64 bytes from 10.0.0.100: icmp_seq=4 ttl=64 time=1.305 ms
      8. 64 bytes from 10.0.0.100: icmp_seq=5 ttl=64 time=1.309 ms
      9. 64 bytes from 10.0.0.100: icmp_seq=6 ttl=64 time=1.247 ms
      10. 64 bytes from 10.0.0.100: icmp_seq=7 ttl=64 time=1.351 ms
      11. 64 bytes from 10.0.0.100: icmp_seq=8 ttl=64 time=1.321 ms
      12. --- nas.ds.net ping statistics ---
      13. 9 packets transmitted, 9 packets received, 0.0% packet loss
      14. round-trip min/avg/max/stddev = 1.032/1.295/1.810/0.211 ms
      Display All
    • Same problem here.
      Same error message, occurring, if I'm not wrong, only when I access OpenMediaVault GUI.
      File transfer, ping and general behaviour seems OK but when accessing GUI (HTTP) connection is often lost then monit generates error message

      Source Code

      1. Connection failed Service nginx
      2. Date: Tue, 10 Mar 2015 17:21:57
      3. Action: restart
      4. Host: [i] myserver_fqdn[/i]
      5. Description: failed protocol test [HTTP] at INET[127.0.0.1:80] via TCP -- HTTP: Error receiving data -- Resource temporarily unavailable
      6. Your faithful employee,
      7. Monit
      8. Connection failed Service nginx
      9. Date: Tue, 10 Mar 2015 17:21:52
      10. Action: restart
      11. Host: [i]myserver_fqdn[/i]
      12. Description: failed protocol test [HTTP] at INET[127.0.0.1:443] via TCPSSL -- HTTP: Error receiving data -- Resource temporarily unavailable
      13. Your faithful employee,
      14. Monit
      Display All


      From openmediavault-webgui_error.log, I get:

      Source Code

      1. 2015/03/10 17:20:13 [error] 20080#0: *135 upstream timed out (110: Connection timed out) while reading response header from upstream, client: ::ffff:192.168.10.103, server: openmediavault-webgui, request: "POST /rpc.php HTTP/1.1", upstream: "fastcgi://unix:/var/run/php5-fpm-openmediavault-webgui.sock:", host: "[i]myserver_fqdn[/i]", referrer: "http://[i]myserver_fqdn[/i]/"


      Increase timeout somewhere in nginx conf may provide some workaround but this is however strange. It was working smoothly previously so I wonder what I changed to generate such error ?(