Search Results

Search results 1-20 of 1,000. There are more results available, please enhance your search parameters.

  • ZFS Hardware requirements

    ryecoaaron - - General

    Post

    It would work fine as long as you don't enable deduplication. zfs will use ram as cache if available. Just remember that if you create a three drive raid z1 (equivalent of mdadm raid 5) pool, that you will have to add three more drives to expand it.

  • Quote from macom: “Do you mean, making several changes via the GUI before clicking Apply? ” Yes. Then you just have one long apply instead of many long applies. I realize there are some cases where this is not possible but I don't have a better solution.

  • OMV 5 uses saltstack for configuration management. It does many more things that older versions of OMV didn't do. On slower systems, this is going to be worse. Not much can be done to avoid this other than wait for all changes before clicking Apply.

  • You need to make the changes to your network/dns setup to get hostname -f working. Once you do that, it should work.

  • OMV Extras Install

    ryecoaaron - - Plugins

    Post

    Seems to be a salt cache issue but I'm not sure how to get to that state or how to prevent it. I will try a few more things. I would consider OMV 5 to be in the release candidate stage.

  • VMWare and iSCSI

    ryecoaaron - - General

    Post

    I wanted to wait to add more notes on the plugin until I knew it was working as expected. Seems like it is. So, I will add some notes and try to make it a little easier to use.

  • I guess if you know it is a bug, file an issue on github. For anything else, posting on the forum is fine. More people see it on the forum. I should see it either way. Glad it is working now.

  • Using NFS mount points as shared points

    ryecoaaron - - NFS

    Post

    You need to use the remotemounts plugin. OMV can't use any mountpoint that it didn't mount.

  • OMV Extras Install

    ryecoaaron - - Plugins

    Post

    Quote from MadX_ZA: “Right now I am at a loss ” Me too. i can't replicate it. Try: apt-get purge openmediavault-omvextrasorg then try the script again.

  • Quote from Speddero: “And since this script was likely crafted by the omv folks when developing the upgrade script, ” codecs.py is a python-maintained script not OMV.

  • Quote from PVasileff: “are you planning porting openmediavault-transmissionbt plugin for OMV5 from OMV4 ? ” Nope. Quote from PVasileff: “people who do not want to use docker only to use tranmissionbt ” If you can come up with a good reason that docker is bad other than inexperience, I will consider it. But I am quite sure a good reason doesn't exist. Quote from PVasileff: “I think - the plugin change only settings in .json file (I am not sure) and if that is true - please port it into OMV5 plugi…

  • I cant install OMV Extras

    ryecoaaron - - Plugins

    Post

    What is the output of: sudo omv-salt deploy run omvextras

  • VMWare and iSCSI

    ryecoaaron - - General

    Post

    Quote from jl524: “Is the target "backing store", the "name" in the shared folders? ” The backing store is a block device. So, that could be a partition without a filesystem, an image file, or the most popular option (in my opinion) is an LVM logical volume. Quote from ness1602: “I guess this works with ZFS? ” It should since zfs can provide a block device (zfs volume). Quote from ness1602: “can you give a simple how-to for this? ” Sure. 1. Wipe a disk in the Physical Disks tab 2. Install the LV…

  • I cant install OMV Extras

    ryecoaaron - - Plugins

    Post

    The output from the install would be helpful. Also, what is the output of dpkg -l | grep openm

  • OMV 5 new behavior

    ryecoaaron - - Network

    Post

    From what I can tell on my test VM, this is a behavior of systemd-networkd. A new mac address isn't stored anywhere in OMV-controlled config files.

  • OMV4 or OMV5

    ryecoaaron - - Updates/Upgrades

    Post

    Quote from draddy: “ut omv5 is "beta" how far away from stable? ” I consider it at the release candidate stage. Quote from draddy: “'m right with omv5 will just go "final" from the beta without reinstall when final is released? ” Yes I would use OMV5. You will just need to move some of your needs to docker.

  • OMV5 Environment Variables

    ryecoaaron - - General

    Post

    Quote from macom: “Seems the GOVERNOR variable is being ignored ” Nope. Just not a perfect grep on my part. /srv/salt/omv/deploy/cpufrequtils/files/cpufrequtils.j2 has this line in it: GOVERNOR="{{ governor }}"

  • You really want to encode video on an RPi? github.com/jlesage/docker-handbrake/issues/48 If you don't want to wait, you could create a simple dockerfile based of debian buster that just installs handbrake from the debian repos.

  • Nanopi crashes on file transfers

    ryecoaaron - - General

    Post

    It is possible it is a kernel issue. I don't have a v2 but my v1 has been ultra stable. Maybe try the 4.4 kernel instead of the 5.4 kernel?

  • Thank you for the comments that you are annoyed. They are very helpful. apt-get purge dhcpcd5 will fix the issue. The install script has been updated.