Smart Error on OMV drive

    • OMV 2.x
    • Smart Error on OMV drive

      Have smart drive status bad on my OMV boot drive. Guessing I need to backup and restore to another drive?

      START OF INFORMATION SECTION ===
      Model Family: Western Digital Caviar Blue Serial ATA
      Device Model: WDC WD1600AAJS-60M0A0
      Serial Number: WD-WMAV35303933
      LU WWN Device Id: 5 0014ee 0abf2cb92
      Firmware Version: 02.03E02
      User Capacity: 160,041,885,696 bytes [160 GB]
      Sector Size: 512 bytes logical/physical
      Device is: In smartctl database [for details use: -P show]
      ATA Version is: 8
      ATA Standard is: Exact ATA specification draft version not indicated
      Local Time is: Wed Feb 3 18:02:31 2016 EST
      SMART support is: Available - device has SMART capability.
      SMART support is: Enabled

      === START OF READ SMART DATA SECTION ===
      SMART overall-health self-assessment test result: PASSED

      General SMART Values:
      Offline data collection status: (0x84) Offline data collection activity
      was suspended by an interrupting command from host.
      Auto Offline Data Collection: Enabled.
      Self-test execution status: ( 0) The previous self-test routine completed
      without error or no self-test has ever
      been run.
      Total time to complete Offline
      data collection: ( 3060) seconds.
      Offline data collection
      capabilities: (0x5b) SMART execute Offline immediate.
      Auto Offline data collection on/off support.
      Suspend Offline collection upon new
      command.
      Offline surface scan supported.
      Self-test supported.
      No Conveyance Self-test supported.
      Selective Self-test supported.
      SMART capabilities: (0x0003) Saves SMART data before entering
      power-saving mode.
      Supports SMART auto save timer.
      Error logging capability: (0x01) Error logging supported.
      General Purpose Logging supported.
      Short self-test routine
      recommended polling time: ( 2) minutes.
      Extended self-test routine
      recommended polling time: ( 40) minutes.
      SCT capabilities: (0x303f) SCT Status supported.
      SCT Error Recovery Control supported.
      SCT Feature Control supported.
      SCT Data Table supported.

      SMART Attributes Data Structure revision number: 16
      Vendor Specific SMART Attributes with Thresholds:
      ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
      1 Raw_Read_Error_Rate POSR-K 200 200 051 - 14
      3 Spin_Up_Time POS--K 138 138 021 - 4075
      4 Start_Stop_Count -O--CK 099 099 000 - 1121
      5 Reallocated_Sector_Ct PO--CK 199 199 140 - 1
      7 Seek_Error_Rate POSR-K 100 253 051 - 0
      9 Power_On_Hours -O--CK 069 069 000 - 22935
      10 Spin_Retry_Count PO--CK 100 100 051 - 0
      11 Calibration_Retry_Count -O--CK 100 100 000 - 0
      12 Power_Cycle_Count -O--CK 099 099 000 - 1114
      184 End-to-End_Error PO--CK 100 100 097 - 0
      187 Reported_Uncorrect -O--CK 100 100 000 - 0
      188 Command_Timeout -O--CK 100 099 000 - 17180131332
      190 Airflow_Temperature_Cel -O---K 069 045 040 - 31
      192 Power-Off_Retract_Count -O--CK 200 200 000 - 134
      193 Load_Cycle_Count -O--CK 200 200 000 - 1121
      196 Reallocated_Event_Count -O--CK 199 199 000 - 1
      197 Current_Pending_Sector -O--CK 200 200 000 - 0
      198 Offline_Uncorrectable ----CK 200 200 000 - 0
      199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
      200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
      ||||||_ K auto-keep
      |||||__ C event count
      ||||___ R error rate
      |||____ S speed/performance
      ||_____ O updated online
      |______ P prefailure warning

      SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
      Device Error Count: 14
      CR = Command Register
      FEATR = Features Register
      COUNT = Count (was: Sector Count) Register
      LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
      LH = LBA High (was: Cylinder High) Register ] LBA
      LM = LBA Mid (was: Cylinder Low) Register ] Register
      LL = LBA Low (was: Sector Number) Register ]
      DV = Device (was: Device/Head) Register
      DC = Device Control Register
      ER = Error register
      ST = Status register
      Powered_Up_Time is measured from power on, and printed as
      DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
      SS=sec, and sss=millisec. It "wraps" after 49.710 days.

      SCT Status Version: 2
      SCT Version (vendor specific): 258 (0x0102)
      SCT Support Level: 1
      Device State: SMART Off-line Data Collection executing in background (4)
      Current Temperature: 31 Celsius
      Power Cycle Min/Max Temperature: 16/43 Celsius
      Lifetime Min/Max Temperature: ?/50 Celsius
      Under/Over Temperature Limit Count: 0/0
      SCT Temperature History Version: 2
      Temperature Sampling Period: 1 minute
      Temperature Logging Interval: 1 minute
      Min/Max recommended Temperature: 0/60 Celsius
      Min/Max Temperature Limit: -41/85 Celsius
      Temperature History Size (Index): 128 (26)

      Index Estimated Time Temperature Celsius
      27 2016-02-03 15:55 31 ************
      ... ..(126 skipped). .. ************
      26 2016-02-03 18:02 31 ************

      SCT Error Recovery Control:
      Read: 85 (8.5 seconds)
      Write: 85 (8.5 seconds)

      SATA Phy Event Counters (GP Log 0x11)
      ID Size Value Description
      0x0001 2 0 Command failed due to ICRC error
      0x0002 2 0 R_ERR response for data FIS
      0x0003 2 0 R_ERR response for device-to-host data FIS
      0x0004 2 0 R_ERR response for host-to-device data FIS
      0x0005 2 0 R_ERR response for non-data FIS
      0x0006 2 0 R_ERR response for device-to-host non-data FIS
      0x0007 2 0 R_ERR response for host-to-device non-data FIS
      0x000a 2 12 Device-to-host register FISes sent due to a COMRESET
      0x8000 4 11435147 Vendor specific