Beim Upgrade omv 2-0 auf 3.0 HDD's unsichtbar

  • Hi all,
    ich dachte, es wird Zeit auf 3.0 zu gehen, also ein 7 Platten-System (2 HDD Pärchen mit jeweils RAID1, ein Stripe mit 2 HDD's und die OMV-Platte) gesichert, platt formatiert mit Parted Magic und neu installiert.
    Im neuen Setup sehe ich alle HDD's unter "Reale Platten", aber kann leider keine neuen Stripes oder RAIDs anlegen.
    Hat jemand eine Idee?
    Gruß, HL

    OMV 2.1
    AN EXAMPLE HOW OLD PC PARTS CAN BE USED:
    Fujitsu-Siemens P5915 (Motherboard D2151-A21), Intel C2D E6600, 4,0 GB DDR RAM, 3Ware RAID controller on PCI slot, up to 6 HDDs in total can be installed due to case changes (currently 2x1tb in RAID1 mode on the board as "holy backup" share & 2x1tb as regular share on 3Ware, one 2tb as storage for two easyVDRs & one 320gb for OMV and ownCloud share), power consumption about 100 Watts (this is OK for that setup...)


    OMV switched on automatically per wol when main PC is switched on...
    OMV switched off per autoshutdown if no IP traffic on main IP over 10 minutes...

  • Hi,
    vielleicht habe ich da irgendwo ein Gedankenfehler, oder hatte sehr viel Glück beim letzten Mal....


    Zu nächst: KEINE Daten verloren, ich bin erstmal absolut "safe".
    Ich wollte 3,0 aufsetzen komplott from scratch..
    Dazu habe ich alle 7 HDDs (6 normale HDD für Daten und ein SSD 32 GB für das OMV Betriebssystem) platt formatiert, in einem Abwasch mit Parted Magic, alle MBR Tabellen neugeschrieben, SSD dran gehängt , omv neu installiert, hochgefahren, kommt hoch sieht aber logischerweise noch keine HDD.
    Dann schliesse ich die HDDs (6 Stück ) ebenfalls an und fahre das OMV ssd hoch, kommt hoch, und ich sehe alle 7 Platten im OMV, soweitso gut...


    Um jetzt meien Platten einzuhängen, mache ich den ersten Schritt wo? RAID VErwaltung, dort müßte ich doch RAID Typ auswühlen und die HDDS wählen: HIER seh ich keine HDDs zum Auswählen....
    Gruß, HL

    OMV 2.1
    AN EXAMPLE HOW OLD PC PARTS CAN BE USED:
    Fujitsu-Siemens P5915 (Motherboard D2151-A21), Intel C2D E6600, 4,0 GB DDR RAM, 3Ware RAID controller on PCI slot, up to 6 HDDs in total can be installed due to case changes (currently 2x1tb in RAID1 mode on the board as "holy backup" share & 2x1tb as regular share on 3Ware, one 2tb as storage for two easyVDRs & one 320gb for OMV and ownCloud share), power consumption about 100 Watts (this is OK for that setup...)


    OMV switched on automatically per wol when main PC is switched on...
    OMV switched off per autoshutdown if no IP traffic on main IP over 10 minutes...

  • Ich glaube, ich habe das Problem gelöst...
    HL

    OMV 2.1
    AN EXAMPLE HOW OLD PC PARTS CAN BE USED:
    Fujitsu-Siemens P5915 (Motherboard D2151-A21), Intel C2D E6600, 4,0 GB DDR RAM, 3Ware RAID controller on PCI slot, up to 6 HDDs in total can be installed due to case changes (currently 2x1tb in RAID1 mode on the board as "holy backup" share & 2x1tb as regular share on 3Ware, one 2tb as storage for two easyVDRs & one 320gb for OMV and ownCloud share), power consumption about 100 Watts (this is OK for that setup...)


    OMV switched on automatically per wol when main PC is switched on...
    OMV switched off per autoshutdown if no IP traffic on main IP over 10 minutes...

    • Offizieller Beitrag

    Um jetzt meien Platten einzuhängen, mache ich den ersten Schritt wo? RAID VErwaltung, dort müßte ich doch RAID Typ auswühlen und die HDDS wählen: HIER seh ich keine HDDs zum Auswählen....

    Soweit korrekt. Die Platten werden nicht angezeigt da sie wohl doch noch irgendwelche Daten enthalten. Um das zu lösen einfach in 'Disks' die Platten formatieren.

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!