OMV can't access the WEbGUI

    • OMV 4.x
    • OMV can't access the WEbGUI

      Hello,

      I've installed OMV 4.1.3 on an intel board with 4 gigas ram and a 250 harddrive and connectind directly from to my router with a cable. The installation seems ok until I boot the system. Let me explain what I've done based on some answers I have found on these forums (many thanks to the OMV community for being so helpful),

      1- When I boot OMV I get an error saying that a network interface was not found.
      2- When I try to access with the admin and openmediavault password the message quickly dissapears and it prompts me again with the user and password.
      3- I have entered the system restore option and with the root password I have checked the ip with "io address command". It says 192.168.0.167. I've tried this ip from my browser and it doesn't connect. I´ve ping this address from Windows and it pings correctly. I am lost. I've also tried connecting to the wrebGUI from my iPhone and it doesn't connects either.
      4- I`ve checked my router and OMV is not connected.
      5- I've tried omv.firstaid and trying to connect the network buy I get an error and I return to the terminal The network card seems working because on the installation I have acceded the debian repositories.

      What else can I do? Can I post some kore information to try to resolve the problem? IT is stange because I had a OMV with Raspberrypi and it work quite well but very slowly. That is why I bought and old mini pc with 4Gb of ram and an Atom proccessor to see if it was faster.


      Many thanks for reading my post. Any help will be appreciated.
    • revise your LAN settings.

      do you use DHCP?.

      Are your OMV DNS correct?.
      OMV 4.1.11 x64 on a HP T510, 16GB CF as Boot Disk & 32GB SSD 2,5" disk for Data, 4 GB RAM, CPU VIA EDEN X2 U4200 is x64 at 1GHz

      Post: HPT510 SlimNAS ; HOWTO Install Pi-Hole ; HOWTO install MLDonkey ; HOHTO Install ZFS-Plugin ; OMV_OldGUI ; ShellinaBOX ; ctop
      Dockers: MLDonkey ; PiHole ; weTTY
      Videos: @TechnoDadLife
    • raulfg3 wrote:

      revise your LAN settings.

      do you use DHCP?.

      Are your OMV DNS correct?.
      First of all many thanks for your help.

      revise your LAN settings.-> How can I check this'? I am a Linux newbie. Should I use the terminal for that?
      do you use DHCP?.-> My router is configured to use DHCP..
      Are your OMV DNS correct?.-> Where do I configure this?

      When I installed the RaspberryPi on a SD card I don't remenber these settings.
    • silikonanswer wrote:

      IT is stange because I had a OMV with Raspberrypi and it work
      You are one of the few users that had less issues on RPi than on x86. May be the only one ;)


      silikonanswer wrote:

      When I try to access with the admin and openmediavault password the message quickly dissapears and it prompts me again with the user and password.
      This is usually the case when the OS drive is full. Have you checked.


      silikonanswer wrote:

      Atom proccessor
      32bit or 64bit?
      Odroid HC2 - armbian - Seagate ST4000DM004 - OMV4.x
      Asrock Q1900DC-ITX - 16GB - 2x Seagate ST3000VN000 - Intenso SSD 120GB - OMV4.x
      :!: Backup - Solutions to common problems - OMV setup videos - OMV4 Documentation - user guide :!:
    • You can try to reconfigure the network interface using omv-firstaid.

      Try to use DHCP on OMV first and make sure the port is 80. Then check on your router which IP has been assigned.
      You can also try to reach OMV by the host name you assigned during installation.

      Finally, if nothing helps post the output of dpkg -l | grep openmedia and df
      Odroid HC2 - armbian - Seagate ST4000DM004 - OMV4.x
      Asrock Q1900DC-ITX - 16GB - 2x Seagate ST3000VN000 - Intenso SSD 120GB - OMV4.x
      :!: Backup - Solutions to common problems - OMV setup videos - OMV4 Documentation - user guide :!:
    • Many thanks for the help. I think there is something wrong related to the router. Sometimes I can't get an ip when installing due to an error in detecting the network. I try on another router at a friend's house and it was detected perfectly. It seems that sometimes my router blocks omv trying to access the network. This is weird because I have other devices connected via cable to this router and they get the ip (nas, Android tv box...). What is wrong with my router configuration? Why it blocks omv accessing the network even on installation? Should I open some ports in the router in order to make it work? And the weirdest thing, why my previos raspberry pi omv installation accesed the network without problems?