after using UnionFS plugin SBC only boots in CLI, no OMV WebGui

    • Resolved
    • OMV 4.x
    • after using UnionFS plugin SBC only boots in CLI, no OMV WebGui

      My SBC suddenly only boots in CLI.

      Source Code

      1. [ 30.650663] D: [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 623; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
      2. [ 30.6595381 mali-utgard ff300000.gpu: Failed to get leakage
      3. [ 30.6678171 mali-utgard ff300000.gpu: Failed to get pvtm
      4. [ 30.6782 76] Mali: Mali device driver loaded
      5. [ 30.7729 65] deufreq ff300000.gpu: Couldn't update frequency transition inforMatim
      6. [ 30.830799 ] FAT-fs Cmmcblk1p6): utf8 is not a recoMmended IO charset for FAT file
      7. [ 31.075696] FAT-fs Cmmcblk1p6): Uolume was not properly unmounted. Some data may be corrupt. Please run fsck.
      8. [ 33.201216] rk_gMac-dwMac ff540000.ethernet eth0: Link is Up - 1Gbps/Full - flow flow control rx/tx
      This is the first time I experience such a behaviour. Previousely I've experimented wit the UnionFS plugin. Something didn't work and therefore I uninstalled the plugin. Then I shut down the board.

      When I run fsck I only get
      fsck from util-linux 2.29.2

      The post was edited 1 time, last by wolf8auer ().

    • I solved it in 2 STEPS.

      I looked at the fstab
      sudo nano /etc/fstab

      Source Code

      1. LABEL=boot /boot/efi vfat defaults,sync 0 0
      2. # >>> [openmediavault]
      3. /dev/disk/by-label/HD01 /srv/dev-disk-by-label-HD01 ext4 defaults,nofail,user_xattr,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,acl 0 2
      4. /dev/disk/by-label/HD02 /srv/dev-disk-by-label-HD02 ext4 defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,acl 0 2
      5. /dev/disk/by-label/parity /srv/dev-disk-by-label-parity ext4 defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,acl 0 2
      6. /dev/disk/by-label/HD03 /srv/dev-disk-by-label-HD03 ext4 defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,acl 0 2
      7. /dev/disk/by-label/320a /srv/dev-disk-by-label-320a ext4 defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,acl 0 2
      8. /srv/dev-disk-by-label-HD03:/srv/dev-disk-by-label-320a /srv/59ef782e-25e3-40b2-94c8-13d6d0e16906 fuse.mergerfs defaults,allow_other,direct_io,use_ino,category.create=epmfs,minfreespace=4G 0 0
      9. # <<< [openmediavault]

      I noticed the last line with fuse.mergerfs
      Since I've created a pool drive with the UnionFS plugin and it didn't work with the shared folder, I've deleted it. I even uninstalled the plugin.
      Unfortunetely I couldn't delete the drive pool in the File Format menu of omv.
      And when I shut down the system and booted again it did't start omv server.

      STEP 1)
      So the solution was to delete the last line from fstab:
      /srv/dev-disk-by-label-HD03:/srv/dev-disk-by-label-320a /srv/59ef782e-25e3-40b2-94c8-13d6d0e16906 fuse.mergerfs defaults,allow_other,direct_io,use_ino,category.create=epmfs,minfreespace=4G 0 0

      After logging into the Web UI I got an error in the File Systems menu.

      STEP 2)
      To fix that I had to remove the disk from the /etc/openmediavault/config.

      Source Code

      1. <mntent>
      2. <uuid>03ed207e-0806-4022-acc4-030f7619142e</uuid>
      3. <fsname>59ef782e-25e3-40b2-94c8-13d6d0e16906</fsname>
      4. <dir>/srv/59ef782e-25e3-40b2-94c8-13d6d0e16906</dir>
      5. <type>fuse.mergerfs</type>
      6. <opts/>
      7. <freq>0</freq>
      8. <passno>0</passno>
      9. <hidden>1</hidden>
      10. </mntent>

      The post was edited 2 times, last by wolf8auer ().

    • Users Online 1

      1 Guest