After dist-upgrade 2>3 no GUI

    • OMV 3.x
    • Resolved
    • Upgrade 2.x -> 3.x

    This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

    • After dist-upgrade 2>3 no GUI

      Hello everybody,
      after performing a dist upgrade from OMV2 to OMV 3.0.99 via putty, I can no longer access my HP Gen8 server via browser via IP. Message "502 Bad Gateway" I no longer have a GUI.
      Access works via Putty, Filezilla and NFS. Can someone give me a tip on how I can get GUI back?
    • You upgraded from one release (2.0) that has been end of life for over 3yrs... to another release that has been end of life for over 2yrs. What could go wrong?

      There's probably a way around this mess, but I would urge you to disconnect your data drives and consider a clean install of either OMV 4 or OMV 5, and then learn to keep your systems properly updated and current
      Air Conditioners are a lot like PC's... They work great until you open Windows.

    • franjo wrote:

      Message "502 Bad Gateway" I no longer have a GUI.
      Try running the following commands in a root shell:

      omv-mkconf nginx

      omv-mkconf php-fpm or omv-mkconf php5fpm

      Reboot.
      --
      Google is your friend and Bob's your uncle!

      RAID - Its ability to disappoint is inversely proportional to the user's understanding of it.

      ASRock Rack C2550D4I C0 Stepping - 16GB ECC - Silverstone DS380

      The post was edited 1 time, last by gderf ().

    • franjo wrote:

      I know, it was my fault to do nothing all the time, but it worked fine in my local network.
      Now I have the idear to integrate my owncloud or something similar and therefore the probs
      Is anywhere a tutorial to do this without losing my data?

      Yeah that's the unfortunate part about not updating... it works great.. until it doesn't. Then you're in this situation. This will probably be a good lesson on keeping things updated.

      Your data should be fine, it's your OS that is the problem (unless you did something really crazy w/ that 2.0 install). As for the OS, at this point you're probably just going to have to start over. It's likely some of the plugins you used on 2.0, are probably not supported anymore (Plex)... so you're going to need to learn to use Docker.

      Like I said, there is likely a way to get around this, but your best bet is to disconnect your data drives (so your data is safe), and reinstall OMV 4 or 5, and start w/ a clean install of OMV.
      Air Conditioners are a lot like PC's... They work great until you open Windows.

    • franjo wrote:

      gderf wrote:

      franjo wrote:

      Message "502 Bad Gateway" I no longer have a GUI.
      Try running the following commands in a root shell:omv-mkconf nginx

      omv-mkconf php-fpm or omv-mkconf php5fpm

      Reboot.
      Error: the script 'usr/share/openmediavault/mkconf/php-fpm' does not exist
      There is an or in that line. Try the second command instead.
      --
      Google is your friend and Bob's your uncle!

      RAID - Its ability to disappoint is inversely proportional to the user's understanding of it.

      ASRock Rack C2550D4I C0 Stepping - 16GB ECC - Silverstone DS380
    • KM0201 wrote:

      franjo wrote:

      I know, it was my fault to do nothing all the time, but it worked fine in my local network.
      Now I have the idear to integrate my owncloud or something similar and therefore the probs
      Is anywhere a tutorial to do this without losing my data?
      Yeah that's the unfortunate part about not updating... it works great.. until it doesn't. Then you're in this situation. This will probably be a good lesson on keeping things updated.

      Your data should be fine, it's your OS that is the problem (unless you did something really crazy w/ that 2.0 install). As for the OS, at this point you're probably just going to have to start over. It's likely some of the plugins you used on 2.0, are probably not supported anymore (Plex)... so you're going to need to learn to use Docker.

      Like I said, there is likely a way to get around this, but your best bet is to disconnect your data drives (so your data is safe), and reinstall OMV 4 or 5, and start w/ a clean install of OMV.
      I've uninstall all plugins bevor upgrade omv extra a.s.o
    • It was worth a try. I think it's too late to try to upgrade to OMV v3 as it's EOL and its repos are all offline.
      --
      Google is your friend and Bob's your uncle!

      RAID - Its ability to disappoint is inversely proportional to the user's understanding of it.

      ASRock Rack C2550D4I C0 Stepping - 16GB ECC - Silverstone DS380
    • I'm not that familiar with the Gen 8's, but Google suggests they are 64bit CPU's.

      Assuming this is accurate...

      Download the ISO for OMV 4, or go ahead and download OMV 5 which should be released any time now.

      Use Etcher to put the ISO on a flash drive. balena.io/etcher/

      Use Flash drive to install to whatever OS drive you want to use. Just make sure when you reinstall, the only drives hooked up are your OS drive, and the Install drive. Do that, and your actual data will be safe.

      When you're done installing/updating... shut down, connect your data drives.

      Boot up, mount your file system and start adding your shares back, etc.
      Air Conditioners are a lot like PC's... They work great until you open Windows.

    • KM0201 wrote:

      I'm not that familiar with the Gen 8's, but Google suggests they are 64bit CPU's.

      Assuming this is accurate...

      Download the ISO for OMV 4, or go ahead and download OMV 5 which should be released any time now.

      Use Etcher to put the ISO on a flash drive. balena.io/etcher/

      Use Flash drive to install to whatever OS drive you want to use. Just make sure when you reinstall, the only drives hooked up are your OS drive, and the Install drive. Do that, and your actual data will be safe.

      When you're done installing/updating... shut down, connect your data drives.

      Boot up, mount your file system and start adding your shares back, etc.
      it works again, thanks to all
      Now OMV 4 is running