shuts down - I think it's temperature but how to check..

Symbiot · Jul 5th 2015

hi

my omv installation shuts down by it self. I think it's temperature caused but am unsure how to check.
is there anywhere in OMV settings I can check? is there any temperature settings I can change?

steel2400 · Jul 5th 2015

hy symbiot,

can you post the cli lines of the moment off install it is possible its something else.

Symbiot · Jul 5th 2015

hi steel

sure.. if you can tell me where to find them.?

it's running as I type.. it's usually during the hottest periods that it shuts down.. which is why I suspect temperature..
I am hoping that I can check somewhere to confirm this?

tekkb · Jul 5th 2015

When you post a question like this please give more information on your system... (e.g. cpu, motherboard, etc...)

steel2400 · Jul 5th 2015

That will help also sorry should have ask't that

Symbiot · Jul 6th 2015

an I should've thought to post it.:

hwinfo --short:

Code

cpu:
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1614 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1607 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1680 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1687 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1615 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1680 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1638 MHz
                       Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz, 1661 MHz
keyboard:
                       American Megatrends Virtual Keyboard and Mouse
mouse:
                       American Megatrends Virtual Keyboard and Mouse
graphics card:
                       Matrox G200 SE A (PCI)
storage:
                       Intel SATA controller
                       LSI Logic / Symbios Logic RAID bus controller
network:
  eth0                 Intel Ethernet controller
  eth1                 Intel 82574L Gigabit Network Connection
network interface:
  eth1                 Ethernet network interface
  eth0                 Ethernet network interface
  lo                   Loopback network interface
disk:
  /dev/sda             LSI MR9271-8i
  /dev/sdb             Corsair CSSD-F18
partition:
  /dev/sda1            Partition
  /dev/sda2            Partition
  /dev/sdb1            Partition
  /dev/sdb2            Partition
  /dev/sdb5            Partition
usb controller:
                       Intel USB Controller
                       Intel USB Controller
bios:
                       BIOS
bridge:
                       Intel Host bridge
                       Intel PCI bridge
                       Intel PCI bridge
                       Intel PCI bridge
                       Intel PCI bridge
                       Intel 82801 PCI Bridge
                       Intel ISA bridge
hub:
                       Linux 3.16.0-0.bpo.4-amd64 ehci_hcd EHCI Host Controller
                       Hub
                       Linux 3.16.0-0.bpo.4-amd64 ehci_hcd EHCI Host Controller
                       Hub
memory:
                       Main Memory
unknown:
                       FPU
                       DMA controller
                       PIC
                       Timer
                       Keyboard controller
                       PS/2 Controller
                       Intel SMBus
  /dev/ttyS0           16550A
  /dev/ttyS1           16550A

Display More

tekkb · Jul 6th 2015

It is a good cpu and a haswell. I doubt it is temp issue if fan is running unless someone did not connect the heatsink properly. It is a 22 nanometer cpu. They run much cooler than the older cpus.

Did you look through your logs around time it shutdown???

Did you look in bios and see what temp said there just for a basis. If it is running hot there then you probably have issue with the heatsink mount.

Give more info., is this self built machine or if you bought what brand/model?

Participate now!