Fl2RAM Plugin - Fstab (/etc/fstab) needs to be changed manually. mandatory ? ?

  • Bcs I use a SSD f OMV systemdrive I installed the openmediavault-flasmemory-1.7 plugin


    In the fl2ram tab you can read : Fstab (/etc/fstab) needs to be changed manually.


    Is this madatory and what is the effect, when or for what needed ? ? ?



    I aslo found only the graph for "Network interfaces " isn't displayed ? ? ? ? ? All other graphs are displayed correct


    Yesterday before I installed flsram all graphs where displayed correct. Known issue ?
    .

    • Offizieller Beitrag

    Did you enable the plugin and reboot?

    omv 7.0.5-1 sandworm | 64 bit | 6.8 proxmox kernel

    plugins :: omvextrasorg 7.0 | kvm 7.0.13 | compose 7.1.4 | k8s 7.1.0-3 | cputemp 7.0.1 | mergerfs 7.0.4


    omv-extras.org plugins source code and issue tracker - github - changelogs


    Please try ctrl-shift-R and read this before posting a question.

    Please put your OMV system details in your signature.
    Please don't PM for support... Too many PMs!

  • Yes I did . Looks like that was wrong ? Then that's my fault.


    But I think it should be expressed more urgent, that before enabling
    the plugin and a restart
    the manual changes should be done.


    Do you see any correlation with the graph problem ? ? ?

    • Offizieller Beitrag

    The order is not important. The manual changes would not affect anything. Not sure what is going on with your graphs. Did you click refresh?

    omv 7.0.5-1 sandworm | 64 bit | 6.8 proxmox kernel

    plugins :: omvextrasorg 7.0 | kvm 7.0.13 | compose 7.1.4 | k8s 7.1.0-3 | cputemp 7.0.1 | mergerfs 7.0.4


    omv-extras.org plugins source code and issue tracker - github - changelogs


    Please try ctrl-shift-R and read this before posting a question.

    Please put your OMV system details in your signature.
    Please don't PM for support... Too many PMs!

  • Yes, I clicked refresh.


    Meanwhile I'v already deinstalled the plugin.


    "The manual changes would not affect anything." For what they then are there mentioned ? That makes no sense to me.


    Is this plugin ( v1.7 ) good for OMV 2.19 ? ? ?


    I'll repair OMV . Can you tell me the repair CLI command pls. THX

    • Offizieller Beitrag

    I meant they wouldn't affect the functionality. The manual changes are just a few more tweaks to eliminate wear on flash media. Everything works fine without them but it isn't the best you can do. Some systems (like RPi) already have the changes done.


    Yes, it is good for OMV 2.19 and any other OMV 2.x version. Very little with the OMV web interface affects the plugin. It would practically work on a plain debian system.


    Repair commands? Not sure what you are talking about. omv-firstaid?

    omv 7.0.5-1 sandworm | 64 bit | 6.8 proxmox kernel

    plugins :: omvextrasorg 7.0 | kvm 7.0.13 | compose 7.1.4 | k8s 7.1.0-3 | cputemp 7.0.1 | mergerfs 7.0.4


    omv-extras.org plugins source code and issue tracker - github - changelogs


    Please try ctrl-shift-R and read this before posting a question.

    Please put your OMV system details in your signature.
    Please don't PM for support... Too many PMs!

    • Offizieller Beitrag

    omv-firstaid fixes setting problems. Try: apt-get install --reinstall openmediavault to reinstall omv without losing anything,

    omv 7.0.5-1 sandworm | 64 bit | 6.8 proxmox kernel

    plugins :: omvextrasorg 7.0 | kvm 7.0.13 | compose 7.1.4 | k8s 7.1.0-3 | cputemp 7.0.1 | mergerfs 7.0.4


    omv-extras.org plugins source code and issue tracker - github - changelogs


    Please try ctrl-shift-R and read this before posting a question.

    Please put your OMV system details in your signature.
    Please don't PM for support... Too many PMs!

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!