Hello guys.
I know I can count on you on this one.
Here is the deal : I did not notice that from the begininng after I moved in my new house, but since then, my network card is set up to 100Mb/s instead of 1Gb/s.
Proof :
tiste@caribounas:/$ sudo ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yesAgain with my switch (Netgear GS116Ev2 - 16-Port Gigabit Ethernet Smart Managed Plus Switch) :
I don't understand why because all the other hardwares are connected with 1000Mb/s autoneg full duplex.
If I try to force autoneg off and speed 1000 on card with :
ethtool -s eth1 speed 1000 duplex full autoneg offI don't get the network starting.
I tried switching the cables on same port on the switch, and between PC and NAS and same...
Everything I plug on the switch, whatever the port, it is autoneg 1000Mb/s OK, so the problem definitely comes from OMV...
Backports are enabled :
More information :
- Hardware on signature
- apt-get update && install done
- eth0 = embedded network card (never been used)
- eth1 = intel PCIe card
- I reinstall these drivers https://downloadcenter.intel.c…sous-Linux-?product=32209 with no luck
Also for your information :
tiste@caribounas:/$ sudo lspci -nnk
01:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Intel Corporation Gigabit CT Desktop Adapter [8086:a01f]
Kernel driver in use: e1000e
Kernel modules: e1000e
03:00.0 Ethernet controller [0200]: Qualcomm Atheros QCA8171 Gigabit Ethernet [1969:10a1] (rev 10)
Subsystem: ASRock Incorporation QCA8171 Gigabit Ethernet [1849:10a1]
Kernel driver in use: alx
Kernel modules: alxtiste@caribounas:/$ lsmod | grep e1000
e1000e 282624 0tiste@caribounas:/$ sudo modprobe e1000e
tiste@caribounas:/$tiste@caribounas:/$ sudo ethtool -i eth0
driver: alx
version:
firmware-version:
expansion-rom-version:
bus-info: 0000:03:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
tiste@caribounas:/$ sudo ethtool -i eth1
driver: e1000e
version: 3.2.6-k
firmware-version: 1.8-0
expansion-rom-version:
bus-info: 0000:01:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: noThanks for you all.
