Docker problem - "Errors were encountered while processing: docker-ce"

placq · 31. Juli 2020

Hi friends,

Couple days ago i started learning OMV. Installed it on Raspberry Pi 4 with one script and everything looks fine exept Docker. In "OMV-Extras" menu when i try to switch ON "Extras repo" the error pops up but the switch turns green.

https://imgur.com/eRauHoV

Next when i try to install docker in "Docker" tab the error from title comes up.

https://imgur.com/PxCyymA

https://imgur.com/Y86PIZV

https://imgur.com/Mc9Te5F

I installed and set up everything with this tutorials:

Installing OMV5 on Raspberry PI's, Armbian SBC's, & i386 32-bit platforms

New User Guide - Getting Started with Openmediavault 4 & 5

Looking for some help

ryecoaaron · 31. Juli 2020

Zitat von placq

when i try to switch ON "Extras repo"

And why do you need the extras repo? There is nothing in it.

Zitat von placq

but the switch turns green.

Since it has to do an apt-get update. I'm guessing your SD card is slow and it is just timing out. The action is still working.

Zitat von placq

Next when i try to install docker in "Docker" tab the error from title comes up.

You need to cut&paste all of the output not just a pic of the end message.

placq · 31. Juli 2020

Hey, heres output you asked

https://pastebin.com/unCrfgv0

ryecoaaron · 31. Juli 2020

What is the output of: sudo apt-get -f install

placq · 31. Juli 2020

Code

Reading package lists... Done
Building dependency tree       
Reading state information... Done
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
1 not fully installed or removed.
After this operation, 0 B of additional disk space will be used.
Setting up docker-ce (5:19.03.12~3-0~debian-buster) ...
Job for docker.service failed because the control process exited with error code.
See "systemctl status docker.service" and "journalctl -xe" for details.
invoke-rc.d: initscript docker, action "start" failed.
● docker.service - Docker Application Container Engine
   Loaded: loaded (/lib/systemd/system/docker.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Fri 2020-07-31 14:53:10 CEST; 20ms ago
     Docs: https://docs.docker.com
  Process: 18423 ExecStart=/usr/bin/dockerd -H fd:// --containerd=/run/containerd/containerd.sock (code=exited, status=1/FAILURE)
 Main PID: 18423 (code=exited, status=1/FAILURE)
dpkg: error processing package docker-ce (--configure):
 installed docker-ce package post-installation script subprocess returned error exit status 1
Errors were encountered while processing:
 docker-ce
E: Sub-process /usr/bin/dpkg returned an error code (1)

Alles anzeigen

ryecoaaron · 31. Juli 2020

sudo journalctl -u docker

placq · 31. Juli 2020

https://pastebin.com/F0R5e1Xh

ryecoaaron · 31. Juli 2020

your lines are all cut off and I can't see the full messages.

placq · 31. Juli 2020

My mistake

https://pastebin.com/TQiusH9J

ryecoaaron · 31. Juli 2020

Can you try use the iptables menu on omv-extras on the docker tab to switch to legacy iptables and then sudo systemctl start docker

placq · 31. Juli 2020

Sure, i got this:

Code

Job for docker.service failed because the control process exited with error code.
See "systemctl status docker.service" and "journalctl -xe" for details.

ryecoaaron · 31. Juli 2020

I need sudo journalctl -u docker again then

placq · 31. Juli 2020

https://pastebin.com/yRMV8Nq3

ryecoaaron · 31. Juli 2020

What about the output of:

lsmod | grep table

placq · 31. Juli 2020

Code

ip_tables              24576  0
x_tables               32768  1 ip_tables

ryecoaaron · 31. Juli 2020

Try:

sudo modprobe iptable_nat

sudo systemctl start docker

placq · 31. Juli 2020

sudo modprobe iptable_nat

Code

modprobe: ERROR: ../libkmod/libkmod.c:586 kmod_search_moddep() could not open moddep file '/lib/modules/4.19.118-v7l+/modules.dep.bin'
modprobe: FATAL: Module iptable_nat not found in directory /lib/modules/4.19.118-v7l+

sudo systemctl start docker

Code

Job for docker.service failed because the control process exited with error code.
See "systemctl status docker.service" and "journalctl -xe" for details.

ryecoaaron · 31. Juli 2020

Just a note. If the first command fails, don't run the next one. I will have to try this on my RPi4. I don't understand what docker's problem is.

placq · 31. Juli 2020

Ok, thanks. I'll wait for news from you.

ryecoaaron · 31. Juli 2020

I wrote a fresh copy of the 5-26 raspbian buster lite to an SD card, booted it, and ran the install script. After that, I logged into the web interface and clicked install docker. No issues. Did you change the docker path?

Docker problem - "Errors were encountered while processing: docker-ce"

Jetzt mitmachen!

Tags