replaced Mobo - cannot set network with omv-firstaid

Hello,

I cloned my system drive + data drives with clonezilla and cannot get the network card working on new motherboard/system.

The new system is an identical PC (Fujitsu Esprimo i5-6500) with identical everything. When I run omv-firstaid to reconfigure the network i get the following error:

ERROR: Failed to connect /var/lib/openmediavault/engine.sock: [Errno 111] Connection refused

Thanks for any help,

David

Here is the network info from the system info dump-file (complete file attached):

================================================================================

= Network interfaces

================================================================================

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000

link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00

inet 127.0.0.1/8 scope host lo

valid_lft forever preferred_lft forever

inet6 ::1/128 scope host

valid_lft forever preferred_lft forever

2: enp0s31f6: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

link/ether 90:1b:0e:96:4c:95 brd ff:ff:ff:ff:ff:ff

--------------------------------------------------------------------------------

Interface information enp0s31f6:

================================

Settings for enp0s31f6:

Supported ports: [ TP ]

Supported link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

1000baseT/Full

Supported pause frame use: No

Supports auto-negotiation: Yes

Supported FEC modes: Not reported

Advertised link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

1000baseT/Full

Advertised pause frame use: No

Advertised auto-negotiation: Yes

Advertised FEC modes: Not reported

Speed: Unknown!

Duplex: Unknown! (255)

Auto-negotiation: on

Port: Twisted Pair

PHYAD: 2

Transceiver: internal

MDI-X: Unknown (auto)

Supports Wake-on: pumbg

Wake-on: g

Current message level: 0x00000007 (7)

drv probe link

Link detected: no

--------------------------------------------------------------------------------

Driver information enp0s31f6:

=============================

driver: e1000e

version: 6.1.0-0.deb11.17-amd64

firmware-version: 0.8-4

expansion-rom-version:

bus-info: 0000:00:1f.6

supports-statistics: yes

supports-test: yes

supports-eeprom-access: yes

supports-register-dump: yes

supports-priv-flags: yes

Didn't help: Following error message

ifup: reading directory /etc/network/interfaces.d /bin/run-parts --exit-on-error --verbose /etc/networkif-pre-up.d

run-parts: executing /etc/network/if-pre-up.d/ethtool

run-parts: executing /etc/network/if-pre-up.d/wireless-tools

run-parts: executing /etc/network/if-pre-up.d/upasupplicant /sbin/ip link set up dev 10 2>/dev/null

ifup: configuring interface lo=lo (inet)

/bin/run-parts --exit-on-error --verbose /etc/network/if-pre-up.d

run-parts: executing /etc/network/if-pre-up.d/ethtool

run-parts: executing /etc/network/if-pre-up.d/wireless-tools

run-parts: executing /etc/network/if-pre-up.d/wpasupplicant /bin/

run-parts --exit-on-error --verbose /etc/network/if-up.d

run-parts: executing /etc/network/if-up.d/chrony

run-parts: executing /etc/network/if-up.d/clamav-freshclam-ifupdown

run-parts: executing /etc/network/if-up.d/ethtool

run-parts: executing /etc/network/if-up.d/postfix

run-parts: executing /etc/network/if-up.d/wpasupplicant /bin/

run-parts --exit-on-error --verbose /etc/network/if-up.d

run-parts: executing /etc/network/if-up.d/chrony

run-parts: executing /etc/network/if-up.d/clamav-freshclam-ifupdoun

run-parts: executing /etc/network/if-up.d/ethtool

run-parts: executing /etc/network/if-up.d/postfix

run-parts: executing /etc/network/if-up.d/wpasupplicant

Hello,

no cables since it is SSD. It boots correctly , however I don't seem to have access to the network adapter.

Ah ok, lol. Ethernet cable worked fine. I chose to move from V6 to V7 and installed OMV V7 from scratch. Thanks for you help.

David

resolved:

I couldn't help myself and dug a little deeper.

WHat finally helped:

replaced the MAC of the old NIC with the MAC of the new NIC in:

etc/netplan/20-openmediavault-enp0s31f6.yaml