Temperature CPU?

jhmiller · Oct 29th 2017

Does it still show when you run sensors

Run sh -x /usr/share/openmediavault/mkconf/sensors and give me the results, remember to only enable the CPU temp.

Ambro72 · Oct 29th 2017

Code

# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +37.0°C  (high = +105.0°C, crit = +105.0°C)
Core 1:       +37.0°C  (high = +105.0°C, crit = +105.0°C)


it8772-isa-0a30
Adapter: ISA adapter
in0:          +0.73 V  (min =  +2.62 V, max =  +2.95 V)  ALARM
in1:          +1.37 V  (min =  +1.66 V, max =  +1.12 V)  ALARM
in2:          +2.00 V  (min =  +2.89 V, max =  +0.37 V)  ALARM
+3.3V:        +3.34 V  (min =  +4.20 V, max =  +4.92 V)  ALARM
in4:          +2.02 V  (min =  +1.45 V, max =  +3.02 V)
in5:          +2.02 V  (min =  +2.62 V, max =  +1.12 V)  ALARM
in6:          +2.22 V  (min =  +0.38 V, max =  +1.62 V)  ALARM
3VSB:         +3.31 V  (min =  +5.71 V, max =  +3.31 V)  ALARM
Vbat:         +3.24 V  
fan1:           0 RPM  (min =   10 RPM)  ALARM
fan2:           0 RPM  (min =   11 RPM)  ALARM
fan3:         336 RPM  (min =   94 RPM)
temp1:        +28.0°C  (low  = -50.0°C, high = +57.0°C)  sensor = thermal diode
temp2:        +25.0°C  (low  = -67.0°C, high = -51.0°C)  ALARM  sensor = thermal diode
temp3:       -128.0°C  (low  = -87.0°C, high =  +0.0°C)  ALARM  sensor = disabled
intrusion0:  ALARM

Display More

and

the attachment for sh -x /usr/share/openmediavault/mkconf/sensors

jhmiller · Oct 29th 2017

Code

rm /usr/share/openmediavault/mkconf/sensors
wget -O /usr/share/openmediavault/mkconf/sensors https://raw.githubusercontent.com/OpenMediaVault-Plugin-Developers/openmediavault-sensors/master/usr/share/openmediavault/mkconf/sensors
chmod +x /usr/share/openmediavault/mkconf/sensors
/usr/share/openmediavault/mkconf/sensors

Update the script again, refresh the webui and then check graphs.

If it still does not work can you check if /var/lib/rrdcached/db/localhost/ has a folder called something like sensors-it877....
If it does have the folder can you re-run the debug command again, making sure you have enabled CPU temp.

Thanks

Ambro72 · Oct 29th 2017

Sorry, but no graphs again....

Code

# ls -al /var/lib/rrdcached/db/localhost/
totale 0
drwxr-xr-x 11 root root 220 ott 27 21:53 .
drwxr-xr-x  3 root root  60 ott 25 02:05 ..
drwxr-xr-x  2 root root 200 ott 25 02:05 cpu-0
drwxr-xr-x  2 root root 200 ott 25 02:05 cpu-1
drwxr-xr-x  2 root root 100 ott 25 02:05 df-root
drwxr-xr-x  2 root root 100 ott 27 21:53 df-srv-dev-disk-by-label-ServerXPDoc
drwxr-xr-x  2 root root 100 ott 25 02:05 interface-eth0
drwxr-xr-x  2 root root  60 ott 25 02:05 load
drwxr-xr-x  2 root root 120 ott 25 02:05 memory
drwxr-xr-x  2 root root 220 ott 25 02:05 rrdcached
drwxr-xr-x  2 root root  80 ott 27 21:19 sensors-coretemp-isa-0000

Display More

I don't have the folder you tell me....

Ambro72 · Nov 5th 2017

Hi,

I tried also to disable coretemp module and refresh sensors with /usr/share/openmediavault/mkconf/sensors but nothing changed in my sad graphics...

Have you new ideas?

Thankyou for assistance.

alexicon · Nov 5th 2017

Helped me.
1. add in /etc/default/grub
GRUB_CMDLINE_LINUX="acpi_enforce_resources=lax"

2. in shell

update-grub2

3. add in /etc/modules
it87

jhmiller · Nov 5th 2017

@Ambro72 You need to have the folder, if it is not there it will not work. See if you can get it to show by following what @alexicon posted above.

Ambro72 · Nov 5th 2017

I follow alexicon's instructions but this is the output:

Code

root@ServerOMV:/var/lib/rrdcached/db/localhost# ls -al
totale 0
drwxr-xr-x 11 root root 220 ott 27 21:53 .
drwxr-xr-x  3 root root  60 ott 25 02:05 ..
drwxr-xr-x  2 root root 200 ott 25 02:05 cpu-0
drwxr-xr-x  2 root root 200 ott 25 02:05 cpu-1
drwxr-xr-x  2 root root 100 ott 25 02:05 df-root
drwxr-xr-x  2 root root 100 ott 27 21:53 df-srv-dev-disk-by-label-ServerXPDoc
drwxr-xr-x  2 root root 100 ott 25 02:05 interface-eth0
drwxr-xr-x  2 root root  60 ott 25 02:05 load
drwxr-xr-x  2 root root 120 ott 25 02:05 memory
drwxr-xr-x  2 root root 220 ott 25 02:05 rrdcached
drwxr-xr-x  2 root root  80 ott 27 21:19 sensors-coretemp-isa-0000

Display More

Of course I relunch commands to regenerate sensors conf... so there isn't the folder.

What is acpi_enforce_resources=lax? I see in internet that may be dangerous for the hardware. Is it safe?

Thankyou

alexicon · Dec 21st 2017

There are plans to make a plug-in for OMV 4?

jhmiller · Dec 21st 2017

The plugin works under OMV 4. I had it installed when i upgraded and it's working fine.

alexicon · Dec 22nd 2017

I installed the plugin on the OMV 4.0.15-1 and switching-on in the Services -> Sensors CPU Temperature, Show Cores and MB Temperature. There were graphs in Diagnostics -> System Informaton -> Performance statistics -> OMV Sensors. But these graphics are not updated, but stand still. The Refresh button does not help. The graphs are updated only if I make the switching-off / switching-on and Save Apply in the Services -> CPU Temperature or Show Cores or MB Temperature or all off/on. The remaining graphics in Performance statistics are updated normally.

Timeless · Dec 30th 2017

Hi,

I've recently tested the plugin on a NanoPi Neo2 and it seems that this CPU temperature sensor is not supported yet.

Code

root@localhost:~# sensors
iio_hwmon-isa-0000
Adapter: ISA adapter
temp1:        +35.2°C

Would it be possible to support a CPU with just 1 temperature sensor?

Regards,
Timeless

tomspatz · Jan 28th 2018

I try to use the plugin on 2 omv machinesfo testing.
Both are running with the 3.16.0-5-amd64.
My issue on the first one ist that only the cpu teperature is showing as a graph all other are "empty".

Code

root@test-nas-01:~# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +42.0°C  (high = +78.0°C, crit = +100.0°C)
Core 1:       +39.0°C  (high = +78.0°C, crit = +100.0°C)


it8721-isa-0a10
Adapter: ISA adapter
in0:          +2.22 V  (min =  +1.03 V, max =  +2.28 V)
in1:          +2.22 V  (min =  +2.75 V, max =  +0.92 V)  ALARM
in2:          +2.22 V  (min =  +2.94 V, max =  +0.64 V)  ALARM
+3.3V:        +3.36 V  (min =  +6.07 V, max =  +5.33 V)  ALARM
in4:          +2.22 V  (min =  +2.99 V, max =  +1.13 V)  ALARM
in5:          +2.22 V  (min =  +2.82 V, max =  +2.69 V)  ALARM
in6:          +2.22 V  (min =  +2.10 V, max =  +0.66 V)  ALARM
3VSB:         +3.29 V  (min =  +5.09 V, max =  +4.15 V)  ALARM
Vbat:         +3.24 V
fan1:         809 RPM  (min =   55 RPM)
fan2:         912 RPM  (min =   13 RPM)
fan3:           0 RPM  (min =   33 RPM)  ALARM
temp1:        +22.0°C  (low  = -17.0°C, high =  -3.0°C)  ALARM  sensor = thermal                                                                             diode
temp2:       -128.0°C  (low  = +57.0°C, high = -68.0°C)  sensor = Intel PECI
temp3:        +22.0°C  (low  = +70.0°C, high = -66.0°C)  ALARM  sensor = Intel P                                                                            ECI
intrusion0:  OK

Display More

any ideas ?

Tom

easygoal · Feb 10th 2018

I installed the latest plugin on OMV4, but complained with the following message

Bash

sudo omv-mkconf sensors


sed: can't read /usr/sbin/omv-mkgraph: No such file or directory

is this omv-mkgraph replaced by something else in OMV4?
My omv4 is installed from scratch.

jackster · Jun 8th 2018

Quote from jhmiller

The plugin works under OMV 4. I had it installed when i upgraded and it's working fine.

But what if you have a fresh install of OMV 4? It is not listed in the plugins list, how can I install it?

jhmiller · Jun 9th 2018

Quote from jackster

But what if you have a fresh install of OMV 4? It is not listed in the plugins list, how can I install it?

You can't.

There is no version compatible with OMV4, and I doubt very much there ever will be, sorry.

Nuke · Apr 1st 2019

Any news for OMV4 ? Almost middle of 2019 is here..

ryecoaaron · Apr 1st 2019

Quote from Nuke

Any news for OMV4 ? Almost middle of 2019 is here..

Nope. No one is working on it.

Participate now!