Posts by exyu74

  • Add 3th NFS Share

    I`m trying to add a 3th Share to same hard disk,but it wont go.


    Here is warning massage:


    Failed to execute command 'export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin; export LANG=C; rm --recursive --force '/export/NetBackup2syn' 2>&1' with exit code '1': rm: cannot remove '/export/NetBackup2syn': Device or resource busy


    Error #0:
    exception 'OMV\ExecException' with message 'Failed to execute command 'export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin; export LANG=C; rm --recursive --force '/export/NetBackup2syn' 2>&1' with exit code '1': rm: cannot remove '/export/NetBackup2syn': Device or resource busy' in /usr/share/php/openmediavault/system/process.inc:175
    Stack trace:
    #0 /usr/share/php/openmediavault/system/mountpoint.inc(117): OMV\System\Process->execute()
    #1 /usr/share/openmediavault/engined/module/fstab.inc(126): OMV\System\MountPoint->unlink()
    #2 [internal function]: OMVModuleFsTab->deleteEntry(Array)
    #3 /usr/share/php/openmediavault/engine/module/moduleabstract.inc(146): call_user_func_array(Array, Array)
    #4 /usr/share/openmediavault/engined/module/fstab.inc(44): OMV\Engine\Module\ModuleAbstract->execTasks('delete')
    #5 /usr/share/openmediavault/engined/rpc/config.inc(152): OMVModuleFsTab->stopService()
    #6 [internal function]: OMVRpcServiceConfig->applyChanges(Array, Array)
    #7 /usr/share/php/openmediavault/rpc/serviceabstract.inc(124): call_user_func_array(Array, Array)
    #8 /usr/share/php/openmediavault/rpc/serviceabstract.inc(150): OMV\Rpc\ServiceAbstract->callMethod('applyChanges', Array, Array)
    #9 /usr/share/php/openmediavault/rpc/serviceabstract.inc(528): OMV\Rpc\ServiceAbstract->OMV\Rpc\{closure}('/tmp/bgstatus4G...', '/tmp/bgoutputoE...')
    #10 /usr/share/php/openmediavault/rpc/serviceabstract.inc(151): OMV\Rpc\ServiceAbstract->execBgProc(Object(Closure))
    #11 /usr/share/openmediavault/engined/rpc/config.inc(213): OMV\Rpc\ServiceAbstract->callMethodBg('applyChanges', Array, Array)
    #12 [internal function]: OMVRpcServiceConfig->applyChangesBg(Array, Array)
    #13 /usr/share/php/openmediavault/rpc/serviceabstract.inc(124): call_user_func_array(Array, Array)
    #14 /usr/share/php/openmediavault/rpc/rpc.inc(86): OMV\Rpc\ServiceAbstract->callMethod('applyChangesBg', Array, Array)
    #15 /usr/sbin/omv-engined(536): OMV\Rpc\Rpc::call('Config', 'applyChangesBg', Array, Array, 1)
    #16 {main}


    Note: There are 2 share`s for backup of laptop with similar names.
    Is there any chance to make 3th share-read only?

  • HPE Proliant Servers

    I would definitely advice third option:
    "use USB only for boot partition, and keep other installation partitions on SSD(on ODD/5th port)

    Quote from Genna

    Hi,
    Connect only your SSD on your Gen8, then, activate in Bios, AHCI (not raid).
    Install OMV on the SSD. Restart.
    After that, OMV will boot on your SSD, without volume raid. Then, with OMV you will be able to create your volume.

    U are not saying where to put ssd :(1) 5th port or (2)front hdd bay?


    1. this option shall work BUT ONLY PARTLY!!!
    Wherever it is needed a reset(bootup)(becouse of reason of whatsoever) of Gen8,
    he NEEDS to get HDD`s OUT of front bay`s before of bootup!!!
    Otherways it will NOT bootup.


    Therefor is boot(grub) on usb stick is needed!!!


    2.That is possible and easy way. Bad side of it is,that he( Mika91) cannot use ssd for more use(saveing) of data on ssd.
    AND the most important, he is LoosinG one bay a front/ in start.

  • OMV Setup Videos

    OpenMediaVault - S.M.A.R.T. management
    [size=12]Next video is not made by me, just stumbled on youtube.


    External Content youtu.be
    Content embedded from external sources will not be displayed without your consent.
    Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.

  • Media Backup OMV3(HP microserver Proliant Gen8) 2 Synology DS215j

    Eric,


    Does u`r option(2) allows me to keep 2nd Nas(DS115j) OFF from time to time and than (after booting up) to continue with rSync/rSnapshot or it needs for the purpose of syncing to be connected by all the time?


    And what do u mean by bolded/underlined text : auxiliary SSD with its own file system?

  • Syncthing

    Hello,


    I use Omv3 and Syncthing 3.11


    I`m trying to set up a folder, but as screenshot say`s i have permission problem.



    Can somebody tell me at least i short steps how to do it?


    Through the forum threads some of user a talking about ACLs,but i`m not willing to do on my own,becouse in the past i messed up Omv with experimentig with ACLs.Or is another way?

  • Rsync, FreeFileSync, and Syncovery

    Quote from geaves

    The latest freefilesync 9.8 via their website runs on debian 9.3, this is probably the reason it will not run, either update OMV or find an earlier version of freefilesync

    Geaves,
    Are u saying that "freefilesync9.0" is possible to use under OMV3 or 4 under Omv GUI or strictly under terminal?

  • Install OMV 4 on new drive and migrate OMV 3 volumes?

    First of all,i`m totaly unknown to ZFS.


    But i may share my experience with other formats.
    In this case was with EXT4 from Sinology Nas on HP Gen8-Omv and it did work without any problem.
    Also once an Omv got crushed by my beginners foult`s and after installing Omv, the same media HDD did work without any problems.


    If u go to install Omv4...put pressent Pc OFF and disconnect media HDD`s as wel external-so there is no need for "unmount" steps.
    Install Omv4 and reconnect all the same as was on Omv3.


    That should do?!


    I just saw...ZFS is possible via plugin.If is the same story with Omv4 do not forget first to install a plugin and than to phisically to reconnect.

  • HPE Proliant Servers

    That depends on u`r hardware setup:


    OpenMediaVault install on:


    1.Usb stick/sd card,
    2.Hard drive,
    3.OpticalDiskDrive-ODD(best sollution)!


    Inform of version 4 is stable?


    If not 3 shall do!



    User Aroundmyroom have place`d his step by step. And i did followd.But did not work for me on the and.
    On internet u can find(if his way does not succeed) another way of doing the same thing.


    Scream if u need help!

  • System Memory Upgrade

    Maybe installing OMV on HPE after mem. upgrade shall get rid of swap?


    But on another hand "the swap" is on my ssd(5th port)....so it`s not so catastrophy.
    Unless u are going to do some heavy job`s with HPE ?

  • System Memory Upgrade

    Quote from David B

    Depending on how much RAM your system has, you may actually be able to completely get rid of the swap partition.

    Well, this is very interesting !


    Does that "rid of swap" happens automatic by Os(OMV) or manualy/by hand ?
    And if is in case of automatic, how much mem is needed to get that to happend theoretical of maximum of supported by motherboard?


    In JohnR and my case HPE Gen8 supports max 16gb ram.


    On another side what user ajaja where talking is very very true a specialy about used-using ram in daily use!

  • USB boot with HP Proliant Microserver gen 8

    Quote from lazydaze

    How were you able to get OMV3 to boot straight from SSD on the 5th bay? I can't seem to get it.

    It is possible 2 use 5th port(ssd/hdd) 2 boot up, BUT ONLY if is no HDD`s in front ray`s!!!
    Otherwise HPE won`t boot up. So,if the server need a reset or putting OFF electrical grid....at boot up(again) hard drives need to be NOT inserted.
    Or BIOS shall recognise hard drive in first slot and say boot up not possible,can not found OS.
    Soooo!!!
    Only and propper way is "internal/motherboard SD/USB stick(Grub) --> 5th port SSD/HDD(OMV) --> Working Great !!!
    In this case is much easyer to install OMV3(64bit) than OMV2(32bit) a specialy when it goes about "grub"-in my case"!!!!!!!!


    Unless u are "booting & using OMV from internal USB stick with or withouth 5th port.

  • Media Backup OMV3(HP microserver Proliant Gen8) 2 Synology DS215j

    Hello guy`s, i have bumped into the wall wit he next warning :


    Please wait, syncing </srv/dev-disk-by-label-1.42.6-5644/video/> to <admin@MediaBackUp::NetBackup> ...


    rsync: getaddrinfo: MediaBackUp 873: Name or service not known
    rsync error: error in socket IO (code 10) at clientserver.c(128) [sender=3.1.1]



    Note:
    I can not get port 873 ON, on the DS215j(It`s reserved only for system) !
    I have tried on both NAS`s port 22 but no result.


    Any advise?

  • Media Backup OMV3(HP microserver Proliant Gen8) 2 Synology DS215j

    Hello everybody,


    I`m looking for an advise or sollution for my aim.


    I have two NAS`s mainly using for as a media dlna. Movies & etc. are on OMV3(HP) and i would like all the media to backup to another NAS which is Synology.
    Synology shall not be on all the time.Only in case of backup.Backup shall be not so often(at least one`s a month or less).


    Now,
    is there a kind(a way or plug-in) of backup that when i press a button for,OMV check`s for a new content on HDD(`s) and the same content sends to Synology?
    So,do not copy`s all the data again and again and again,which may take on the and a few lightyears...
    Both NASes are locally(on the same router).


    TNX!