Posts by Fornax

    dmesg

    Code
    [    6.209275] mt7601u 1-1.4:1.0: ASIC revision: 76010001 MAC revision: 76010500
    [    6.218389] mt7601u 1-1.4:1.0: Direct firmware load for mt7601u.bin failed with error -2
    [    6.219038] mt7601u: probe of 1-1.4:1.0 failed with error -2
    [    6.219230] usbcore: registered new interface driver mt7601u

    the output of iwconfig and nmtui-connect are the same

    Why does everyone plays around with ifconfig?


    Experience with other solution, better or worst i dont know, just wanted to express thats on other solutions it worked and how.


    Code
    lsusb
    iwconfig
    dmesg
    nmtui-connect


    Code
    Bus 001 Device 008: ID 0bc2:3300 Seagate RSS LLC
    Bus 001 Device 007: ID 0bc2:3323 Seagate RSS LLC
    Bus 001 Device 005: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
    Bus 001 Device 014: ID 148f:7601 Ralink Technology, Corp.
    Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
    Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


    Code
    eth0      no wireless extensions.
    
    
    lo        no wireless extensions.


    Code
    [14018.286247] usb 1-1.4: USB disconnect, device number 11
    [16384.182921] usb 1-1.2: new high-speed USB device number 12 using dwc_otg
    [16385.472871] usb 1-1.4: new high-speed USB device number 13 using dwc_otg
    [16386.522924] usb 1-1.2: new high-speed USB device number 14 using dwc_otg
    [16386.664842] usb 1-1.2: New USB device found, idVendor=148f, idProduct=7601
    [16386.664859] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [16386.664867] usb 1-1.2: Product: 802.11 n WLAN
    [16386.664874] usb 1-1.2: Manufacturer: MediaTek
    [16386.664881] usb 1-1.2: SerialNumber: 1.0
    [16386.872838] usb 1-1.2: reset high-speed USB device number 14 using dwc_otg
    Code
    nmtui:ERROR:nmt-newt-listbox.c:333:update_active_internal: assertion failed: (priv->active >= 0 && priv->active < priv->entries->len)
                                                                                                                                           Aborted

    Steps are

    • burn image with Etcher
    • connect Raspberry Pi to Ethernet (needs Internet connection on first boot)
    • insert SD card, power on board, wait until green led stops blinking (this is after the reboot)
    • check OMV UI, it has to report latest OMV 3 version (3.0.94 at the time of this writing) and latest RPi kernel version (something above 4.9.41)

    If step 4 displays anything else something with steps 1 to 3 went wrong (your Wi-Fi will never work) and you have to start over again. The above procedure is not important wrt Wi-Fi (since too slow anyway) but to get a fully working OMV install on Raspberries.

    • check
    • check
    • check yesterday he had about 6H time

    i will try it again


    the installation with or without the wifi dongle?

    Hallo,


    i have installed the OMV_3_0_88_RaspberryPi_2_3_4.9.4 image on a Raspberry Pi 2. Im trying to install mine WiFi dongle with chip 7601.
    Maybe i missed the part where the solution for mine problem has been posted, please direct me to it.
    nmtui-connect got the same error message as flmaxey.
    From mine experience with raspian jessie i had to connect the dongle and it appears in the interface list
    ifconfig -a
    Here is that not the case
    Im new in Linux and Raspberry.
    I would like post the raport from armbianmonitor, but got an response that sounds "500 internal Server error"
    Any help appreciate. Thanks in advance.