Does your NAS connect @1GBit with other Switches or so, you may have lying around?
Looks like a defective NIC for me
I have an 1Gbps connection but the NAS is negotiating with the router on 100Mbps.
02:00.0 Ethernet controller: Broadcom Limited NetXtreme BCM5764M Gigabit Ethernet PCIe (rev 10)
root@NAS:~# ip link show
enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 00:26:2d:29:3e:16 brd ff:ff:ff:ff:ff:ff
I can´t see an issue...what am I doing wrong
Is there a reason running pi-hole@docker?
My pi-hole is running fine direct on my OMV hardware, just moving OMV to Port 81and you are done.
What the hell is going on, #9 is under moderation? Why?Quote
Dieser Beitrag muss zunächst von einem Moderator geprüft und freigeschaltet werden, damit er für alle Benutzer sichtbar wird.
I don't recommend this for most users. Not only do you install a newer version not intended for your system but now it won't get updates. This could be easily scripted to work with existing version of wipefs.
Do you have the output when it showed the 30 offsets? That would let me write a one liner to wipe everything instead of updating util-linux.
No, I didn´t install anything...Quote
It didn´t show the 30 offsets at a time. It shows them one by one. You have to copy each Hex offset seperately reported by
until no more ZFS offsets are shown. Thats all. Nothing to install
ananas, you´re the man!
After copying has finished, I unmounted the partition and tried with the onboard wipefs.
Kinda work, it showed 30 (!) different offsets. Deleted them all and anything is back again, including disk usage.
Thanks so much!
Alas, this should be pinned for everyone who is in this trouble...
ananas, looks promising (Partition is shown as ZFS-Member in wipefs).
Can´t go further yet, still copying data from the drive...
Question in advance: where and how to download util-linux-2.32?
Will it not interfere with the installed wipefs?
thanks for the quick answer. Interesting, I never created a Raid. I did some investigation and found that
finds all that is needed, I think...
seems to do something, but blkid does not show anything afterwards...
I will copy the disk at first and go to play around; there must be an easier way, I think
no, the data disk is not killed, the data is there and can be manually mounted. This as a foreword...
Upgrade did fine so far, but there are strange things happening with the data drive. It is found under disks, fine:
But looking at file systems shows...
Disk usage is complete empty:
Completely missing here:
Things that may be helpful:CodeCodecgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,release_agent=/lib/systemd/systemd-cgroups-agent,name=systemd)cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio)systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=30,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=12497)
Anything else needed?
Can please someone help me outta this? Thanks in advance...
Edit: And I receive mails like:
It started so often this day
Its cheap and unimportant enough to take the risk
There is enough power on the 4-pin floppy connector. Running fine for hours
since my secondary backup NAS (Zyxel NSA310 w/Debian) has left the building some days ago, I was thinking about an easy and cheap solution holding a single drive. I came to that:
Cost 23,90€ on Ebay.
I used a 3,5" 3TB HDD drive instead the mentioned 2,5", pulled of my defective Zyxel. Drive is lying on the PCI-Slot (no need for any screw), power and data cables reside over the RAM-Banks. The lid will close (keeping the drive in position), really fine.
This cable is shorter than described; don´t go for it with a 2,5". You have to find a longer one for that case.
mSATA SSD Drive 32GB: https://www.amazon.de/gp/product/B01N9ZWJV2 as system drive. Cost: 14€, now slightly more
Not the fastest, not the best, but cheap enough to give it a try.
Parts are all in place and lid closed, so I´ll take it to work and install debian, than OMV.
I will report and when its ready, I´ll make a photo.