Posts by kubidootwo

  • OMV7 to OMV8 Bad Gateway 502

    Disappointed No help. It appears I was able to fix via this information below. I am sure others will have this issue.


    Understanding the 502 Bad Gateway Error

    The 502 Bad Gateway error occurs when a server acting as a gateway or proxy receives an invalid response from an upstream server. This can happen during various operations, including logging into the OpenMediaVault (OMV) web interface after an upgrade.


    Common Causes


    Upgrade Issues

    • PHP Version Mismatch: After upgrading from OMV 7 to OMV 8, the system may still reference an outdated PHP version (like PHP 7.4) instead of the required version (like PHP 8.2).
    • Nginx Configuration: The Nginx configuration may not be updated correctly during the upgrade, leading to errors when trying to access the web interface.


    Client-Side Problems

    • Browser Cache: Sometimes, cached data in your browser can cause issues. Clearing the cache may resolve the problem.


    Solutions


    Server-Side Fixes

    1. Run Deployment Commands:
      • Execute the command: sudo omv-salt stage run deploy to update configurations and services.
    2. Check Nginx Configuration:
      • Ensure that the Nginx configuration is pointing to the correct PHP version. You can test the configuration with sudo nginx -t.
    3. Restart Services:
      • Restart Nginx and PHP services to apply changes:
        • sudo systemctl restart nginx
        • sudo systemctl restart php8.4-fpm (or the relevant PHP version).(
          To find the PHP version used by OpenMediaVault 8 (OMV8), you can log into the OMV web interface, navigate to the "System" section, and then check the "Information" or "About" page where the PHP version is typically displayed. Alternatively, you can run the command php -v in the terminal if you have access to the command line.)


    Client-Side Fixes

    • Clear Browser Cache: Clear your browser's cache and try accessing the web interface again.
    • Try Different Browsers: If the issue persists, try accessing the interface using a different browser or in incognito mode.

    By following these steps, you should be able to resolve the 502 Bad Gateway error after upgrading to OMV 8.

  • OMV7 to OMV8 Bad Gateway 502

    I am opening a new question on the 502 gateway error. I have read and applied the fixes(* below for reference)on this forum and thru searches.

    The Last omvupgrade said updating from 8.07 to 8.08 still no change.

    I have tried running commands thru Putty and directly with keyboard and monitor to the HP i3 desktop.

    Continue to get broken pipe error thru Putty. 502 bad gateway thru chrome(also in incognito). I have not tried any other browsers.

    Rebooted pc and laptop a few times during installations, still bad gateway.

    I do not know what I am missing

    If logs are needed, let me know.

    Thanks,

    k



    ----------------

    *

    A "502 Bad Gateway" error after an OpenMediaVault (OMV) upgrade typically occurs because the web server (NGINX) cannot communicate with the backend service (PHP-FPM) due to interrupted installation steps or configuration mismatches.

    To resolve this on OMV 8 (Synchrony), follow these steps:

    1. Run the Official Fix Script

    The OMV developers provide a script to specifically address upgrade-related 502 errors and broken PHP-FPM configurations.

    Log in to your server via SSH or use a physical keyboard/monitor.Execute the following command as root:

    wget -O - https://raw.githubusercontent.com | bash


    2. Repair Broken Packages

    If the script does not fully resolve the issue, manually trigger a package repair to ensure all dependencies are correctly installed for Debian 13 (the base for OMV 8).

    Configure interrupted packages: sudo dpkg --configure -aFix broken dependencies: sudo apt-get -f installRun a final upgrade check: sudo omv-upgrade


    3. Verify PHP-FPM Status

    OMV 8 uses a different PHP version than previous releases. If NGINX is still trying to communicate with an older or masked PHP service, the gateway error will persist.

    Check if the current PHP-FPM service is running: systemctl status php*-fpmIf you see errors regarding php7.4-fpm or php8.2-fpm being masked or missing, the fix script in Step 1 is the primary way to re-align these to the OMV 8 defaults.


    4. Clear Browser Cache

    Sometimes the error is cached in your browser even after the server is fixed.

    Perform a hard refresh: Ctrl + Shift + R (Windows/Linux) or Cmd + Shift + R (Mac).Try accessing the WebUI in an Incognito/Private window

  • Errors -

    This worked to restart. We will see if its permanent on next restart.


    Code
    sudo systemctl restart console-setup.service

  • Errors -

    Zafkiel I was able to run the code after Soma code recommendations.

    The error did Not appear on reboot. Thank You :) :)

    Only 2 Newer issues left --- console.service did not load

    Updated to 7.4-15 lost connection, had dpkg --configure -a to run, but still shows update. I even tried to rerun from console, no change.

    k

  • Errors -

  • Errors -

  • Errors -

    @Zafkiel

    See below tried a couple of different locations for files, errors with no such directory

    My linux is not very good

    k


    <sudo wget -O /usr/lib/firmware/i915/kbl_dmc_ver1_04.bin https://git.kernel.org/pub/scm…/i915/kbl_dmc_ver1_04.bin

    /usr/lib/firmware/i915/kbl_dmc_ver1_04.bin: No such file or directory

    root@jnas:~# sudo wget -O /usr/lib/firmware/i915/kbl_dmc_ver1_04.bin https://git.kernel.org/pub/scm…/i915/kbl_dmc_ver1_04.bin

    /usr/lib/firmware/i915/kbl_dmc_ver1_04.bin: No such file or directory>

  • Errors -

    I have successfully updated, no updates available. I still get i915 error. I have googled an forum says regenerate intrafms ie for boot, no change

    Another says to do this:

    Code:
    CONFIG_EXTRA_FIRMWARE="intel-ucode/06-8e-09 i915/kbl_dmc_ver1_04.bin"
    CONFIG_EXTRA_FIRMWARE_DIR="/lib/firmware"


    Can anyone let me know if I should do this?

    Any other ideas or Thoughts??


    k

  • Errors -

    Zafkiel

    I am not home, but believe the setup is a=hdd, b=ssd(omv storage), c=12gb usb running omv., d=usb hdd for backup

    What would have changed recently to not load intel graphics driver? Google search shows more than a couple years old for this error.

    Thanks for the response and future help.

    k

  • Errors -

    I noticed the following errors after the recent update.


    Background fyi. HP machine with i3, must hit F9 to chose file to load due to UEFI(just fyi, Always been this way)

    I do this directly on keyboard attached and viewed on monitor.


    This past Monday, needed to do many updates and the following errors were notice via monitor.

    No arrays found in config file or automatically /dev/sdc2; recovering journal

    {15.0945] i915 0000:00:02.0 firmware: failed to load i915/kbl_dmc_ver1_04.bin (-2)

    It will eventually load and let me log in. Very Slow.


    I seen today more updates are ready. I tried to load:

    Failed to execute command 'export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin; export LC_ALL=C.UTF-8; export LANGUAGE=; export DEBIAN_FRONTEND=noninteractive; apt-get --yes --allow-downgrades --allow-change-held-packages --fix-broken --fix-missing --auto-remove --allow-unauthenticated --show-upgraded --option DPkg::Options::="--force-confold" dist-upgrade 2>&1' with exit code '100': E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem.


    I tried to run dpkg.... at the keyboard . These will not load, and stayed unconfigured.


    I googled and did not see any forum responses.

    Are these errors interelated?

    What are some recommendation?


    Thanks for the help in advance,

    k

  • Is there a guide to in place upgrade?

    Quote from Soma

    Your file is jibberish.


    Code
    PK    7¼´X^Æ2'   '      mimetypeapplication/vnd.oasis.opendocument.textPK  7¼´X            '   Configurations2/accelerator/current.xml PK           PK    7¼´X               Configurations2/images/Bitmaps/PK    7¼´X               Configurations2/floater/PK    7¼´X               Configurations2/progressbar/PK    7¼´X               Configurations2/menubar/PK    7¼´X               Configurations2/popupmenu/PK    7¼´X               Configurations2/statusbar/PK    7¼´X               Configurations2/toolbar/PK    7¼´X               Configurations2/toolpanel/PK    7¼´XKÄÏ;  Ï;     Thumbnails/thumbnail.png‰PNG

   
IHDR   Æ      g?ž  ;–IDATxœí};rãJ“uNÄ,€ÁÐ
fV€¡CKîõ¦MþŽ¼6éÉ™2åÊ¢ÃÁ
´ƒ ÷òý•¯z¡ð†º‰æ«&A P ‹ÀÁ©s2ÿý_ÿú<âëÅ¿ÿé<âo‹ÇzÄÊñRX9Cê+ÇcH=båx©G¬!õˆ•ã1¤±r<†Ô#VŽÇzÄÊñRX9Cê+ÇcH=båx©G¬!õˆ•ã1¤±r<†Ô#VŽÇzÄʱpHÝn7Ȳìv«(sÀ¿e†Ë«Ê¼oÌŸð%/ä•ýÍÛªªJ³ø+ÄkêÕÛŽÇrjMMÜÊëdÿÊØsyoNÌ¥}žC£§¦¯K³ðÞbþªÞÞê¢8–% hª[Vâ_ÀÖ ä­-Z§±iÞÌ™®A¿,\O7¾¨Ì 54øI]›}u
P¼UoP€ÿÑró·ØéÛÂ.™wfEÐO‹bõ¼Ð­x5ómãO¿Ê}Q_p/²3¸\.×ëçîðQ@SK'yÅcÞ¼ýsºþüx7œÓx©š¦>Ÿáð‚=1»‘cÍÜžÈsÙجqÈ»ó7¼óXp•ÂÓ®q£S#!“óä¢ãwY‡­[˜/#ß7
õ­•ÛU÷ø-ÒÆPÔEnG/ h¨Y»•y½+€¯ Ò­fš©/M~Ì̾ŠýÞ,¡½Pû¹iß¼ù|Ú¿`ìžs3Ôš›ùÊŸŸ¾âú
Ê=\hhïöÞïˆû,§£á½èÇÕ¸,J3à/Þ†wó‡Té_[Ì[ï¯YF§;+yE<¿¼.Þ!u´åyy<Ò¹xà’,³-©    zwÔâU¬Â›H.»/¡äfñŸÓ­%Ó«žÝê®p”¦pó£÷Üs+ey”ƹ¶…ã‘ŽS?£·Yx³ÊÝ Ï¤›t>Žt°tÏ2ÜÁˆäîo˜—Óoá¿=V†ç­«~æäØ’™Ÿ“—înÎmçij_Ûc™±¸FòÄ}Õµpó~A×°'ˆ“Ì]IoUý‘å8úé^™ìpUÝðÐøã,D`²»¡»×‡SÆp2Ú{WTÕ[žïg@ÆïˆeXª¸à
MÞÌ

    This is output from putty, copied and put into text per directions. What Next?