Beiträge von mtganzer

Re: Plex native vs in Docker: Plex says they don't support hardware transcoding inside a Docker container. This is kind of important to those of us trying to use lower-powered CPU's that support it. I do know my way around Linux enough to load the Plex .deb natively, but others may not.

https://support.plex.tv/articl…re-accelerated-streaming/

"Can I use Hardware-Accelerated Streaming inside of Docker?
At this time, we do not formally support hardware acceleration inside of a Docker container. Some users of Docker (on Linux only) have been able to accomplish this by adding platform-specific custom configurations that expose host hardware to the container."

Looks interesting...but would probably also want to flash the uBoot as well. At this point, I am satisfied because I achived my objective of replacing Arch with Debian (I spend most of my time with Ubuntu and Redhat, and Arch was just a complete oddball trying to manage). My NSA320 is mainly just a backup destination for the VM's in my ESXi home lab. OMV piqued my interest because of iSCSI support, but really don't need it at the moment.

Since we are drifting off-topic here, I will defer any further discussion to the doozan forums (just joined there)

Definitely NOT an annoyance...appreciate all the help!!!

Tried the change with the 32GB stick, and unfortunately still no-go. Sees 2 USB devices, but 0 USB storage devices. The more I look at it, the more it looks like the braindead USB subsystem in the stock uBoot.

At this point, probably will put this aside for a bit. I did some hacking of the install script to enable the hard drive boot options you had commented out, and installed to the SATA drive using Bodhi's 3.17 rootfs as you described in your thread over on doozan.

Here was is where I left off trying with the USB boot.

NSA320>> printenv

bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootdelay=2
baudrate=115200
loads_echo=0
ethaddr=00:19:CB:00:51:81
eth1addr=00:19:CB:00:51:82
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=DD01
PRODUCT_NAME=NSA-320
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=ZyXEL Communications Corp.
run_diag=yes
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
bootcmd_linux_usb_0=ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd ; bootm $(loadaddr) 0x01100000
bootcmd_linux_usb_1=ext2load usb 1:1 $(loadaddr) /uImage; ext2load usb 1:1 0x01100000 /uInitrd ; bootm $(loadaddr) 0x01100000
bootcmd_linux_usb_2=ext2load usb 2:1 $(loadaddr) /uImage ; ext2load usb 2:1 0x01100000 /uInitrd ; bootm $(loadaddr) 0x01100000
bootcmd_stock=setenv mainlineLinux no; setenv bootargs $(bootargs_stock); nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000
bootcmd=run pre_bootcmd_linux_usb; run bootcmd_linux_usb_0; run bootcmd_linux_usb_1; run bootcmd_linux_usb_2; run bootcmd_stock; reset
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
ethprime=egiga1
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
disaMvPnp=no
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
hddPowerCtrl=no
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
ethact=egiga1
pre_bootcmd_linux_usb=setenv mainlineLinux yes; setenv bootargs $(bootargs_linux); usb reset

Environment size: 2712/131068 bytes
NSA320>> saveenv

Saving Environment to NAND...
Erasing Nand...Writing to Nand... done

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Mar 23 2011 - 16:09:39) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
//--- stateButtonBit = 3, recovery ---//
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]
Hit any key to stop autoboot: 2 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number

NAND read: device 0 offset 0x4640000, size 0xa00000

Different errors now. Wonder if I messed up the 32GB USB stick when I nuked it (really just deleted partitions using fdisk).

- Pulled the HD (helps to RTFM - DOH!)
- resetenv;reset
- boots from install USB, writes to 32G USB, shuts down. Check 32GB USB on RPi, all the files look like they are where they need to be.
- put 32 GB USB back USB2 port on NSA320, power up:

** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Mar 23 2011 - 16:09:39) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
//--- stateButtonBit = 3, recovery ---//
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]
Hit any key to stop autoboot: 2 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number

NAND read: device 0 offset 0x4640000, size 0xa00000

(continues booting from nand with stick Zyxel firnware)

Going to have to go out and get another USB stick or 2 (will try 16 GB this time), but will be another couple days.

FYI the 32GB drive is a "SanDisk Ultra Fit™ CZ43 32GB USB 3.0 Low-Profile Flash Drive".

I have re-imaged it back to stock Zyxel software (4.70) now. I was trying to install using what was in your dropbox on Sept 1. Install USB was 8 GB SanDisk, formatted FAT32, contents:
-rwxr-xr-x 1 root root 29593600 May 24 19:36 boot-nsa320.tar
-rwxr-xr-x 1 root root 1190 Aug 6 03:47 creating salted checksums.txt
-rwxr-xr-x 1 root root 721582080 Jul 12 06:52 debian-omv-stoneburner1.tar
-rwxr-xr-x 1 root root 31980 Feb 18 2010 md5sum
-rwxr-xr-x 1 root root 64 Sep 5 2012 nsa310_check_file_C0
-rwxr-xr-x 1 root root 64 Mar 16 2012 nsa310_check_file_C0.libzy.so
-rwxr-xr-x 1 root root 3993 Aug 5 19:06 README.txt
-rwxr-xr-x 1 root root 36 Jun 14 2012 salted_md5sum
-rwxr-xr-x 1 root root 36 Jun 14 2012 salted_md5sum_3x0
-rwxr-xr-x 1 root root 23 Sep 5 2012 usb_key_func.sh
-rwxr-xr-x 1 root root 14085 Aug 11 05:17 usb_key_func.sh.2

No error log being generated.

Boot files in in boot partition on 32GB SanDisk USB drive. I have it mounted on my RPi now:
Disk /dev/sda: 31.1 GB, 31104958464 bytes
64 heads, 32 sectors/track, 29664 cylinders, total 60751872 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sda1 2048 206847 102400 83 Linux
/dev/sda2 206848 60751871 30272512 83 Linux

Boot partition is ext2, rootfs is ext4 (again currently mounted on the RPi)
/dev/sda1 on /mnt/boot type ext2 (rw,relatime)
/dev/sda2 on /mnt/rootfs type ext4 (rw,relatime,data=ordered)

Listing of the boot partition:
-rw-r--r-- 1 root root 129088 Oct 22 2014 config-3.17.0-kirkwood-tld-1
drwxr-xr-x 2 root root 4096 May 23 06:36 dts
-rw-r--r-- 1 root root 7597358 May 22 19:25 initrd.img-3.17.0-kirkwood-tld-1
drwx------ 2 root root 12288 Sep 3 18:36 lost+found
-rw-r--r-- 1 root root 0 May 25 02:36 nsa320
-rw-r--r-- 1 root root 1991026 Oct 22 2014 System.map-3.17.0-kirkwood-tld-1
-rw-r--r-- 1 root root 2835406 May 24 07:16 uImage
-rw-r--r-- 1 root root 7597422 May 24 07:17 uInitrd
-rwxr-xr-x 1 root root 2822168 Oct 22 2014 vmlinuz-3.17.0-kirkwood-tld-1
-rwxr-xr-x 1 root root 2822168 Oct 22 2014 zImage-3.17.0-kirkwood-tld-1
-rwxr-xr-x 1 root root 2835342 May 24 07:14 zImage.fdt

Note that was after I manually untarred the boot-nsa320.tar into the boot partition. I have tried to nuke the 32GB key, but for some reason the install script isn't finding it during the install (bad USB stick or bad USB port on the back of the NSA320?). Probably at the point I need to go back to the beginning and do a full capture of the install script output.

It looks like all the files are where they are supposed to be on a 32 GB SanDisk USB key. But for some reason it doesn't find the kernel image (/boot/uImage) on the USB, and it then falls back to booting from the old nand image. Same thing happens when I try to load to SATA drive. I have am currently UART booting from the 2014.07 U-boot.

Here is the U-boot environment:

arcNumber=3956
baudrate=115200
bootcmd=run bootcmd_uenv; run bootcmd_usb; usb stop; run bootcmd_sata; reset
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=b6:d0:5e:0f:a1:17
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=118f
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=nand_mtd:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
partition=nand0,2
rootdelay=10
rootfstype=ext2
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_load=usb start; setenv uenv_loaded 0; for devtype in usb; do for disknum in 0; do run uenv_read_disk; done; done
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if $devtype part $disknum; then run uenv_read; fi
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

Environment size: 2084/131068 bytes
---------------------

Below is console output during boot process:
-----------------

NSA320> boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0 -- Partition Type: DOS

PartStart SectorNum SectorsUUIDType
12048 204800 00000000-0183
2206848 60545024 00000000-0283
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** File not found /boot/uImage **
** File not found /boot/uInitrd **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
stopping USB..

Reset IDE: Bus 0: OK Bus 1: not available
Device 0: Model: WDC WD20EFRX-68AX9N0 Firm: 80.00A80 Ser#: WD-WMC301133227
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512)
** Invalid partition 1 **
** Invalid partition 1 **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
resetting ...

Anyone tried the installing from a previously-reflashed to arch NSA320? I seem to get all the way through the install, but it doesn't look like uboot updates properly, and upon next boot, it uses the default Zyxel enviornment. I have tried the "setenv to_factory; saveenv" and "resetenv", but neither works.