smartctl -a /dev/sdb smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.19.0-0.bpo.4-amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA100 Serial Number: 565YRA7MS LU WWN Device Id: 5 000039 fe9cd8296 Add. Product Id: DELL(tm) Firmware Version: MS2OA7S0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Dec 9 19:02:14 2019 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7216) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 121) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 001 001 016 Pre-fail Always FAILING_NOW 4294967295 2 Throughput_Performance 0x0004 001 001 000 Old_age Offline - 8215 3 Spin_Up_Time 0x0007 128 128 024 Pre-fail Always - 176 (Average 181) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 93 5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1913 7 Seek_Error_Rate 0x000a 100 100 000 Old_age Always - 0 8 Seek_Time_Performance 0x0004 110 110 000 Old_age Offline - 36 9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 26088 10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 93 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 934 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 934 194 Temperature_Celsius 0x0002 203 203 000 Old_age Always - 27 (Min/Max 18/54) 196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2096 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 001 001 000 Old_age Offline - 13185 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0012 097 097 000 Old_age Always - 26085 241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 3745037962 242 Total_LBAs_Read 0x0012 100 100 000 Old_age Always - 662974576 SMART Error Log Version: 1 ATA Error Count: 3006 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3006 occurred at disk power-on lifetime: 26088 hours (1087 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 68 00 00 00 40 00 00:03:06.361 READ FPDMA QUEUED ec 00 01 00 00 00 40 00 00:03:06.359 IDENTIFY DEVICE ef 05 fe 00 00 00 40 00 00:03:06.359 SET FEATURES [Enable APM] ef 10 02 00 00 00 a0 00 00:03:06.357 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:03:06.357 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 3005 occurred at disk power-on lifetime: 26088 hours (1087 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 08 00 00 00 Error: UNC at LBA = 0x00000008 = 8 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 40 08 00 00 40 00 00:03:02.305 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:03:02.303 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:03:02.303 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 00:03:02.301 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 00:03:02.301 SET FEATURES [Set transfer mode] Error 3004 occurred at disk power-on lifetime: 26088 hours (1087 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 a8 08 00 00 40 00 00:02:58.258 READ FPDMA QUEUED 60 08 a0 00 00 00 40 00 00:02:58.258 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:02:58.255 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:02:58.255 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 00:02:58.252 IDENTIFY DEVICE Error 3003 occurred at disk power-on lifetime: 26088 hours (1087 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 30 08 00 00 40 00 00:02:54.224 READ FPDMA QUEUED 60 08 08 00 00 00 40 00 00:02:54.224 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:02:54.224 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:02:54.223 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 00:02:54.221 IDENTIFY DEVICE Error 3002 occurred at disk power-on lifetime: 26088 hours (1087 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 a8 00 00 00 40 00 00:02:50.279 READ FPDMA QUEUED 60 08 a0 00 00 00 40 00 00:02:50.279 READ FPDMA QUEUED 60 08 e0 a0 6d 70 40 00 00:02:50.279 READ FPDMA QUEUED 60 08 98 a0 6d 70 40 00 00:02:50.279 READ FPDMA QUEUED 60 08 d8 00 6d 70 40 00 00:02:50.258 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14805 - # 2 Extended offline Completed without error 00% 14742 - # 3 Short offline Completed without error 00% 14740 - # 4 Short offline Completed without error 00% 14603 - # 5 Short offline Completed without error 00% 14435 - # 6 Short offline Completed without error 00% 14267 - # 7 Short offline Completed without error 00% 14099 - # 8 Short offline Completed without error 00% 13931 - # 9 Short offline Completed without error 00% 13763 - #10 Short offline Completed without error 00% 13595 - #11 Short offline Completed without error 00% 13427 - #12 Short offline Completed without error 00% 13259 - #13 Short offline Completed without error 00% 13091 - #14 Short offline Completed without error 00% 12923 - #15 Short offline Completed without error 00% 12755 - #16 Short offline Completed without error 00% 12587 - #17 Short offline Completed without error 00% 12419 - #18 Short offline Completed without error 00% 12084 - #19 Short offline Completed without error 00% 11916 - #20 Short offline Completed without error 00% 11748 - #21 Short offline Completed without error 00% 11580 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.