Drive SDA : === START OF INFORMATION SECTION === Device Model: WDC WD50EFRX-68MYMN1 Serial Number: XX LU WWN Device Id: 5 0014ee 2b5adfb73 Firmware Version: 82.00A82 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Not recognized. Minor revision code: 0x001f Local Time is: Fri Dec 19 09:41:38 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (58320) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 204 204 021 - 8758 4 Start_Stop_Count -O--CK 100 100 000 - 140 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 382 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 30 192 Power-Off_Retract_Count -O--CK 200 200 000 - 13 193 Load_Cycle_Count -O--CK 200 200 000 - 495 194 Temperature_Celsius -O---K 114 104 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x30 has 9 sectors [Reserved] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 32 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 32 [7] occurred at disk power-on lifetime: 382 hours (15 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:11:09.593 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:11:09.593 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:09.593 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:09.592 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:09.591 SMART WRITE LOG Error 31 [6] occurred at disk power-on lifetime: 371 hours (15 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:39:32.942 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:39:32.942 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:39:32.942 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:39:32.941 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 16:39:32.941 SMART READ LOG Error 30 [5] occurred at disk power-on lifetime: 371 hours (15 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:39:32.933 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 16:39:32.933 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:39:32.932 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:39:32.932 SMART WRITE LOG 2f 00 00 00 01 00 00 00 00 00 07 40 08 16:39:32.931 READ LOG EXT Error 29 [4] occurred at disk power-on lifetime: 371 hours (15 days + 11 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 a8 05 28 e0 40 00 Error: WP at LBA = 0xa80528e0 = 2818910432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 58 00 d0 00 00 ac 63 1f d8 40 08 16:24:43.324 WRITE FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 16:08:13.623 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 16:08:08.628 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 15:38:15.423 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 15:38:10.427 CHECK POWER MODE Error 28 [3] occurred at disk power-on lifetime: 274 hours (11 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 00 01 50 00 fe 00 40 00 Error: IDNF at LBA = 0x15000fe00 = 5637209600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 40 00 00 90 37 1d 10 40 08 01:34:35.570 READ FPDMA QUEUED 60 00 50 00 38 00 00 90 37 1c c0 40 08 01:34:35.570 READ FPDMA QUEUED 60 00 58 00 30 00 00 90 37 1b b8 40 08 01:34:35.570 READ FPDMA QUEUED 60 00 58 00 28 00 00 90 37 1b 60 40 08 01:34:35.570 READ FPDMA QUEUED 60 01 00 00 20 00 00 90 37 25 30 40 08 01:34:35.553 READ FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 272 hours (11 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 11:58:33.952 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 11:58:33.952 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 11:58:33.951 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 11:58:33.950 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 11:58:33.950 SMART READ LOG Error 26 [1] occurred at disk power-on lifetime: 269 hours (11 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:43:35.544 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:43:35.544 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:43:35.544 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:43:35.543 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:43:35.543 SMART READ LOG Error 25 [0] occurred at disk power-on lifetime: 269 hours (11 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:43:35.536 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 08:43:35.536 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:43:35.536 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:43:35.535 SMART WRITE LOG 2f 00 00 00 01 00 00 00 00 00 07 40 08 08:43:35.534 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 269 - # 2 Extended offline Completed without error 00% 255 - # 3 Extended offline Aborted by host 90% 245 - # 4 Extended offline Aborted by host 90% 245 - # 5 Extended offline Aborted by host 90% 245 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 27/40 Celsius Lifetime Min/Max Temperature: 23/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (148) Index Estimated Time Temperature Celsius 149 2014-12-19 01:44 38 ******************* ... ..( 67 skipped). .. ******************* 217 2014-12-19 02:52 38 ******************* 218 2014-12-19 02:53 39 ******************** ... ..(244 skipped). .. ******************** 463 2014-12-19 06:58 39 ******************** 464 2014-12-19 06:59 40 ********************* ... ..( 95 skipped). .. ********************* 82 2014-12-19 08:35 40 ********************* 83 2014-12-19 08:36 39 ******************** ... ..( 19 skipped). .. ******************** 103 2014-12-19 08:56 39 ******************** 104 2014-12-19 08:57 38 ******************* ... ..( 43 skipped). .. ******************* 148 2014-12-19 09:41 38 ******************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 97870 Vendor specific Drive SDB: == START OF INFORMATION SECTION === Device Model: WDC WD50EFRX-68MYMN1 Serial Number: XX LU WWN Device Id: 5 0014ee 2b5b57496 Firmware Version: 82.00A82 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Not recognized. Minor revision code: 0x001f Local Time is: Fri Dec 19 09:42:23 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (57180) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 201 201 021 - 8916 4 Start_Stop_Count -O--CK 100 100 000 - 7 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 85 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 5 192 Power-Off_Retract_Count -O--CK 200 200 000 - 0 193 Load_Cycle_Count -O--CK 200 200 000 - 44 194 Temperature_Celsius -O---K 117 112 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x30 has 9 sectors [Reserved] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 40 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 85 hours (3 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:11:57.664 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:57.664 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:57.664 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:57.663 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:57.663 SMART READ LOG Error 3 [2] occurred at disk power-on lifetime: 85 hours (3 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:11:57.657 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:11:57.657 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 1d+03:11:57.656 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:57.655 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:11:57.654 SMART WRITE LOG Error 2 [1] occurred at disk power-on lifetime: 75 hours (3 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:39:54.925 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:39:54.925 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:39:54.924 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:39:54.923 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 16:39:54.923 SMART READ LOG Error 1 [0] occurred at disk power-on lifetime: 74 hours (3 days + 2 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 a8 05 28 e0 40 00 Error: WP at LBA = 0xa80528e0 = 2818910432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 58 00 c8 00 00 ac 63 1f 80 40 08 16:24:44.824 WRITE FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 16:08:30.081 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 16:08:25.086 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 15:38:31.830 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 15:38:26.835 CHECK POWER MODE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 27/40 Celsius Lifetime Min/Max Temperature: 24/40 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (285) Index Estimated Time Temperature Celsius 286 2014-12-19 01:45 39 ******************** ... ..(292 skipped). .. ******************** 101 2014-12-19 06:38 39 ******************** 102 2014-12-19 06:39 40 ********************* ... ..(119 skipped). .. ********************* 222 2014-12-19 08:39 40 ********************* 223 2014-12-19 08:40 39 ******************** ... ..( 11 skipped). .. ******************** 235 2014-12-19 08:52 39 ******************** 236 2014-12-19 08:53 38 ******************* ... ..( 13 skipped). .. ******************* 250 2014-12-19 09:07 38 ******************* 251 2014-12-19 09:08 37 ****************** ... ..( 6 skipped). .. ****************** 258 2014-12-19 09:15 37 ****************** 259 2014-12-19 09:16 36 ***************** ... ..( 14 skipped). .. ***************** 274 2014-12-19 09:31 36 ***************** 275 2014-12-19 09:32 35 **************** ... ..( 9 skipped). .. **************** 285 2014-12-19 09:42 35 **************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 14 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 97918 Vendor specific Drive SDC: opyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD50EFRX-68MYMN1 Serial Number: XXXX LU WWN Device Id: 5 0014ee 2b5b5be38 Firmware Version: 82.00A82 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Not recognized. Minor revision code: 0x001f Local Time is: Fri Dec 19 09:43:13 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (58320) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 100 253 021 - 0 4 Start_Stop_Count -O--CK 100 100 000 - 6 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 37 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 4 192 Power-Off_Retract_Count -O--CK 200 200 000 - 0 193 Load_Cycle_Count -O--CK 200 200 000 - 32 194 Temperature_Celsius -O---K 116 111 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x30 has 9 sectors [Reserved] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 40 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 37 hours (1 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:12:44.923 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+03:12:44.923 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:12:44.923 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:12:44.922 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:12:44.922 SMART READ LOG Error 4 [3] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 a8 05 28 e0 40 00 Error: WP at LBA = 0xa80528e0 = 2818910432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 58 00 a8 00 00 ac 63 1f 28 40 08 16:24:43.628 WRITE FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 16:08:33.893 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 16:08:28.898 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 15:38:35.666 CHECK POWER MODE e5 00 00 00 00 00 00 00 00 00 00 00 08 15:38:30.671 CHECK POWER MODE Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:21:33.614 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:21:33.613 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:21:33.613 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:21:33.612 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:21:33.612 SMART READ LOG Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:04:44.148 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:04:44.147 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:04:44.147 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:04:44.146 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:04:44.146 SMART READ LOG Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:01:37.715 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:01:37.715 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:01:37.714 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:01:37.713 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:01:37.713 SMART READ LOG SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 28/41 Celsius Lifetime Min/Max Temperature: 24/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (369) Index Estimated Time Temperature Celsius 370 2014-12-19 01:46 40 ********************* ... ..(255 skipped). .. ********************* 148 2014-12-19 06:02 40 ********************* 149 2014-12-19 06:03 41 ********************** ... ..(156 skipped). .. ********************** 306 2014-12-19 08:40 41 ********************** 307 2014-12-19 08:41 40 ********************* ... ..( 9 skipped). .. ********************* 317 2014-12-19 08:51 40 ********************* 318 2014-12-19 08:52 39 ******************** ... ..( 12 skipped). .. ******************** 331 2014-12-19 09:05 39 ******************** 332 2014-12-19 09:06 38 ******************* ... ..( 10 skipped). .. ******************* 343 2014-12-19 09:17 38 ******************* 344 2014-12-19 09:18 37 ****************** ... ..( 6 skipped). .. ****************** 351 2014-12-19 09:25 37 ****************** 352 2014-12-19 09:26 36 ***************** ... ..( 16 skipped). .. ***************** 369 2014-12-19 09:43 36 ***************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 97966 Vendor specific Drive SDE: START OF INFORMATION SECTION === Device Model: WDC WD50EFRX-68MYMN1 Serial Number: XXX LU WWN Device Id: 5 0014ee 20b0315f8 Firmware Version: 82.00A82 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Not recognized. Minor revision code: 0x001f Local Time is: Fri Dec 19 09:43:48 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (58800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 202 201 021 - 8900 4 Start_Stop_Count -O--CK 100 100 000 - 151 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 374 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 35 192 Power-Off_Retract_Count -O--CK 200 200 000 - 16 193 Load_Cycle_Count -O--CK 200 200 000 - 524 194 Temperature_Celsius -O---K 118 105 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x30 has 9 sectors [Reserved] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 40 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 23 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 23 [22] occurred at disk power-on lifetime: 364 hours (15 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:25.098 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:25.093 SMART READ LOG 61 00 b0 00 30 00 00 9a c1 e1 a8 40 08 16:40:25.093 WRITE FPDMA QUEUED b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:25.093 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:40:25.092 SMART WRITE LOG Error 22 [21] occurred at disk power-on lifetime: 364 hours (15 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:25.093 SMART READ LOG 61 00 b0 00 30 00 00 9a c1 e1 a8 40 08 16:40:25.093 WRITE FPDMA QUEUED b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:25.093 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:40:25.092 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:40:25.091 SMART WRITE LOG Error 21 [20] occurred at disk power-on lifetime: 267 hours (11 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 00 01 50 01 00 10 40 00 Error: IDNF at LBA = 0x150010010 = 5637210128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 90 00 00 93 a9 19 40 40 08 01:36:40.545 READ FPDMA QUEUED 60 00 50 00 88 00 00 93 a9 18 f0 40 08 01:36:40.545 READ FPDMA QUEUED 61 00 68 00 80 00 01 50 01 00 10 40 08 01:36:40.535 WRITE FPDMA QUEUED 60 00 50 00 78 00 00 93 a9 03 00 40 08 01:36:40.533 READ FPDMA QUEUED 60 00 58 00 70 00 00 93 a8 eb a8 40 08 01:36:40.533 READ FPDMA QUEUED Error 20 [19] occurred at disk power-on lifetime: 262 hours (10 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:42:05.879 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:42:05.879 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:42:05.878 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:42:05.877 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:42:05.877 SMART READ LOG Error 19 [18] occurred at disk power-on lifetime: 262 hours (10 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:42:05.871 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:42:05.870 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 08:42:05.870 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:42:05.869 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:42:05.868 SMART WRITE LOG Error 18 [17] occurred at disk power-on lifetime: 262 hours (10 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:35:10.032 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:35:10.031 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:35:10.030 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:35:10.029 SMART WRITE LOG 2f 00 00 00 01 00 00 00 00 00 11 40 08 08:35:10.029 READ LOG EXT Error 17 [16] occurred at disk power-on lifetime: 262 hours (10 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:34:56.813 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:34:56.813 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:34:56.812 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:34:56.811 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:34:56.811 SMART READ LOG Error 16 [15] occurred at disk power-on lifetime: 262 hours (10 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:34:44.630 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:34:44.630 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:34:44.629 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:34:44.627 SMART WRITE LOG 2f 00 00 00 01 00 00 00 00 00 11 40 08 08:34:44.627 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 275 - # 2 Short offline Completed without error 00% 262 - # 3 Extended offline Aborted by host 90% 262 - # 4 Extended offline Aborted by host 90% 261 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 27/39 Celsius Lifetime Min/Max Temperature: 23/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (195) Index Estimated Time Temperature Celsius 196 2014-12-19 01:46 38 ******************* ... ..(284 skipped). .. ******************* 3 2014-12-19 06:31 38 ******************* 4 2014-12-19 06:32 39 ******************** ... ..(127 skipped). .. ******************** 132 2014-12-19 08:40 39 ******************** 133 2014-12-19 08:41 38 ******************* ... ..( 9 skipped). .. ******************* 143 2014-12-19 08:51 38 ******************* 144 2014-12-19 08:52 37 ****************** ... ..( 11 skipped). .. ****************** 156 2014-12-19 09:04 37 ****************** 157 2014-12-19 09:05 36 ***************** ... ..( 8 skipped). .. ***************** 166 2014-12-19 09:14 36 ***************** 167 2014-12-19 09:15 35 **************** ... ..( 9 skipped). .. **************** 177 2014-12-19 09:25 35 **************** 178 2014-12-19 09:26 34 *************** ... ..( 16 skipped). .. *************** 195 2014-12-19 09:43 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 14 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 98002 Vendor specific Drive SDF: = START OF INFORMATION SECTION === Device Model: WDC WD50EFRX-68MYMN1 Serial Number: XXX LU WWN Device Id: 5 0014ee 2b5ae81f3 Firmware Version: 82.00A82 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Not recognized. Minor revision code: 0x001f Local Time is: Fri Dec 19 09:44:14 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (57840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 192 191 021 - 9383 4 Start_Stop_Count -O--CK 100 100 000 - 150 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 374 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 33 192 Power-Off_Retract_Count -O--CK 200 200 000 - 14 193 Load_Cycle_Count -O--CK 200 200 000 - 506 194 Temperature_Celsius -O---K 120 108 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x30 has 9 sectors [Reserved] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 40 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 27 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 27 [2] occurred at disk power-on lifetime: 374 hours (15 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:13:44.821 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:13:44.821 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:13:44.821 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:13:44.820 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+03:13:44.820 SMART READ LOG Error 26 [1] occurred at disk power-on lifetime: 374 hours (15 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:13:44.813 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f 09 00 08 1d+03:13:44.813 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+03:13:44.812 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+03:13:44.812 SMART WRITE LOG 2f 00 00 00 01 00 00 00 00 00 07 40 08 1d+03:13:44.811 READ LOG EXT Error 25 [0] occurred at disk power-on lifetime: 363 hours (15 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:48.216 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 16:40:48.216 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:40:48.215 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 16:40:48.214 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 16:40:48.214 SMART READ LOG Error 24 [23] occurred at disk power-on lifetime: 296 hours (12 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 00 00 a3 3d 91 80 40 00 Error: IDNF at LBA = 0xa33d9180 = 2738721152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 d8 00 00 1b b3 72 20 40 08 07:33:17.930 READ FPDMA QUEUED 60 00 08 00 d0 00 00 1b b3 72 c8 40 08 07:33:17.907 READ FPDMA QUEUED 61 00 08 00 c8 00 00 a3 3d 91 80 40 08 07:33:17.889 WRITE FPDMA QUEUED 60 00 08 00 c0 00 00 1b b3 72 d0 40 08 07:33:17.868 READ FPDMA QUEUED 61 00 10 00 b8 00 00 a3 3d 91 60 40 08 07:33:17.858 WRITE FPDMA QUEUED Error 23 [22] occurred at disk power-on lifetime: 266 hours (11 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 40 00 00 fc ce 39 d8 40 00 Error: IDNF at LBA = 0xfcce39d8 = 4241373656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 48 00 20 00 00 93 43 4a a8 40 08 01:12:11.173 READ FPDMA QUEUED 61 00 08 00 18 00 00 fc ce 39 d8 40 08 01:12:11.163 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 a3 34 2c 40 40 08 01:12:11.153 WRITE FPDMA QUEUED 60 00 58 00 08 00 00 93 43 49 f0 40 08 01:12:11.143 READ FPDMA QUEUED 60 00 50 00 00 00 00 93 43 49 40 40 08 01:12:11.142 READ FPDMA QUEUED Error 22 [21] occurred at disk power-on lifetime: 261 hours (10 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:43:23.834 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:43:23.834 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:43:23.833 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:43:23.832 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:43:23.832 SMART READ LOG Error 21 [20] occurred at disk power-on lifetime: 261 hours (10 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:41:10.308 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:41:10.307 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:41:10.307 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:41:10.306 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:41:10.305 SMART READ LOG Error 20 [19] occurred at disk power-on lifetime: 261 hours (10 days + 21 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 0b 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:36:24.689 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:36:24.688 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:36:24.687 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:36:24.686 SMART WRITE LOG 2f 00 00 00 01 00 00 00 00 00 11 40 08 08:36:24.686 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 261 - # 2 Extended offline Aborted by host 90% 261 - # 3 Extended offline Aborted by host 80% 261 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 27/37 Celsius Lifetime Min/Max Temperature: 24/44 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (342) Index Estimated Time Temperature Celsius 343 2014-12-19 01:47 35 **************** ... ..( 18 skipped). .. **************** 362 2014-12-19 02:06 35 **************** 363 2014-12-19 02:07 36 ***************** ... ..(341 skipped). .. ***************** 227 2014-12-19 07:49 36 ***************** 228 2014-12-19 07:50 37 ****************** ... ..( 40 skipped). .. ****************** 269 2014-12-19 08:31 37 ****************** 270 2014-12-19 08:32 36 ***************** ... ..( 14 skipped). .. ***************** 285 2014-12-19 08:47 36 ***************** 286 2014-12-19 08:48 35 **************** ... ..( 14 skipped). .. **************** 301 2014-12-19 09:03 35 **************** 302 2014-12-19 09:04 34 *************** ... ..( 9 skipped). .. *************** 312 2014-12-19 09:14 34 *************** 313 2014-12-19 09:15 33 ************** ... ..( 10 skipped). .. ************** 324 2014-12-19 09:26 33 ************** 325 2014-12-19 09:27 32 ************* ... ..( 16 skipped). .. ************* 342 2014-12-19 09:44 32 ************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 13 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 15 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 98027 Vendor specific