=== START OF INFORMATION SECTION === Model Family: HGST Travelstar 7K1000 Device Model: HGST HTS721010A9E630 Serial Number: JR1004BN2H1V8M LU WWN Device Id: 5 000cca 8d8e30782 Firmware Version: JB0OA3U0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Mar 26 14:02:26 2021 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 171) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 163 163 040 - 91 3 Spin_Up_Time POS--- 119 119 033 - 2 4 Start_Stop_Count -O--C- 100 100 000 - 420 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 138 138 040 - 34 9 Power_On_Hours -O--C- 045 045 000 - 24286 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 418 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 274 193 Load_Cycle_Count -O--C- 100 100 000 - 2627 194 Temperature_Celsius -O---- 181 181 000 - 33 (Min/Max 13/58) 196 Reallocated_Event_Count -O--CK 100 100 000 - 52 197 Current_Pending_Sector -O---K 100 100 000 - 24 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 18947 hours (789 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 50 00 00 6d 9f 3a 30 0d 00 Error: UNC at LBA = 0x6d9f3a30 = 1839151664 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 f0 00 00 6d 9f 39 80 40 08 2d+00:16:55.560 READ FPDMA QUEUED 60 01 00 00 e8 00 00 6d 9f 38 80 40 08 2d+00:16:55.550 READ FPDMA QUEUED 60 01 00 00 e0 00 00 6d 9f 37 80 40 08 2d+00:16:55.549 READ FPDMA QUEUED 60 01 00 00 d8 00 00 6d 9f 36 80 40 08 2d+00:16:55.539 READ FPDMA QUEUED 60 01 00 00 d0 00 00 6d 9f 35 80 40 08 2d+00:16:55.537 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 17572 hours (732 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 c0 00 00 73 89 18 40 03 00 Error: UNC at LBA = 0x73891840 = 1938364480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 40 00 00 73 89 14 00 40 08 1d+23:58:16.549 READ FPDMA QUEUED 61 00 04 00 38 00 00 1f 6e a8 10 40 08 1d+23:58:16.549 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 1d+23:58:16.547 FLUSH CACHE EXT 60 00 80 00 20 00 00 73 89 13 80 40 08 1d+23:58:16.498 READ FPDMA QUEUED 60 00 80 00 18 00 00 73 89 13 00 40 08 1d+23:58:16.498 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 17571 hours (732 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 b8 00 00 72 e1 9b 48 02 00 Error: UNC at LBA = 0x72e19b48 = 1927387976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 80 00 50 00 00 72 e1 96 80 40 08 1d+23:50:10.962 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 1d+23:50:10.932 FLUSH CACHE EXT 60 05 80 00 38 00 00 72 e1 91 00 40 08 1d+23:50:10.931 READ FPDMA QUEUED 61 00 01 00 30 00 00 02 54 10 08 40 08 1d+23:50:10.930 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 1d+23:50:10.918 FLUSH CACHE EXT Error 1 [0] occurred at disk power-on lifetime: 17571 hours (732 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 03 80 00 00 70 cd d1 00 00 00 Error: UNC at LBA = 0x70cdd100 = 1892536576 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 03 80 00 a0 00 00 70 cd d1 00 40 08 1d+23:28:02.558 READ FPDMA QUEUED 61 00 20 00 98 00 00 17 dd c8 00 40 08 1d+23:28:02.427 WRITE FPDMA QUEUED 60 05 00 00 90 00 00 70 cd cc 00 40 08 1d+23:28:02.427 READ FPDMA QUEUED 61 00 08 00 88 00 00 11 9f fd b0 40 08 1d+23:28:02.427 WRITE FPDMA QUEUED 60 07 00 00 80 00 00 70 cd c5 00 40 08 1d+23:28:02.427 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 24285 - # 2 Short offline Completed without error 00% 24284 - # 3 Short offline Completed without error 00% 24283 - # 4 Short offline Completed without error 00% 24282 - # 5 Short offline Completed without error 00% 24281 - # 6 Short offline Completed without error 00% 24280 - # 7 Short offline Completed without error 00% 24279 - # 8 Short offline Completed without error 00% 24278 - # 9 Short offline Completed without error 00% 24277 - #10 Short offline Completed without error 00% 24276 - #11 Short offline Completed without error 00% 24275 - #12 Short offline Completed without error 00% 24274 - #13 Short offline Completed without error 00% 24273 - #14 Short offline Completed without error 00% 24272 - #15 Short offline Completed without error 00% 24271 - #16 Short offline Completed without error 00% 24270 - #17 Short offline Completed without error 00% 24269 - #18 Short offline Completed without error 00% 24268 - #19 Short offline Completed without error 00% 24267 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 31/35 Celsius Lifetime Min/Max Temperature: 13/58 Celsius Lifetime Average Temperature: 42 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (22) Index Estimated Time Temperature Celsius 23 2021-03-26 11:55 33 ************** 24 2021-03-26 11:56 32 ************* ... ..( 3 skipped). .. ************* 28 2021-03-26 12:00 32 ************* 29 2021-03-26 12:01 33 ************** 30 2021-03-26 12:02 33 ************** 31 2021-03-26 12:03 32 ************* ... ..( 2 skipped). .. ************* 34 2021-03-26 12:06 32 ************* 35 2021-03-26 12:07 33 ************** 36 2021-03-26 12:08 32 ************* 37 2021-03-26 12:09 32 ************* 38 2021-03-26 12:10 32 ************* 39 2021-03-26 12:11 33 ************** 40 2021-03-26 12:12 33 ************** 41 2021-03-26 12:13 32 ************* 42 2021-03-26 12:14 32 ************* 43 2021-03-26 12:15 32 ************* 44 2021-03-26 12:16 33 ************** 45 2021-03-26 12:17 32 ************* 46 2021-03-26 12:18 32 ************* 47 2021-03-26 12:19 33 ************** 48 2021-03-26 12:20 32 ************* 49 2021-03-26 12:21 32 ************* 50 2021-03-26 12:22 32 ************* 51 2021-03-26 12:23 33 ************** 52 2021-03-26 12:24 33 ************** 53 2021-03-26 12:25 32 ************* 54 2021-03-26 12:26 33 ************** ... ..( 59 skipped). .. ************** 114 2021-03-26 13:26 33 ************** 115 2021-03-26 13:27 34 *************** ... ..( 12 skipped). .. *************** 0 2021-03-26 13:40 34 *************** 1 2021-03-26 13:41 33 ************** 2 2021-03-26 13:42 34 *************** 3 2021-03-26 13:43 33 ************** 4 2021-03-26 13:44 33 ************** 5 2021-03-26 13:45 34 *************** ... ..( 3 skipped). .. *************** 9 2021-03-26 13:49 34 *************** 10 2021-03-26 13:50 33 ************** 11 2021-03-26 13:51 34 *************** 12 2021-03-26 13:52 33 ************** 13 2021-03-26 13:53 34 *************** 14 2021-03-26 13:54 34 *************** 15 2021-03-26 13:55 33 ************** 16 2021-03-26 13:56 34 *************** ... ..( 2 skipped). .. *************** 19 2021-03-26 13:59 34 *************** 20 2021-03-26 14:00 33 ************** 21 2021-03-26 14:01 34 *************** 22 2021-03-26 14:02 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 65535+ Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS