smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.10.0-0.bpo.9-amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: WD-WCC4N1005319 LU WWN Device Id: 5 0014ee 25f63fe94 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Dec 10 17:16:19 2021 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (38400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 385) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 358 3 Spin_Up_Time POS--K 176 172 021 - 6183 4 Start_Stop_Count -O--CK 097 097 000 - 3014 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 037 036 000 - 46474 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 253 192 Power-Off_Retract_Count -O--CK 200 200 000 - 123 193 Load_Cycle_Count -O--CK 198 198 000 - 8237 194 Temperature_Celsius -O---K 122 109 000 - 28 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 199 199 000 - 615 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 196 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 37 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37 [12] occurred at disk power-on lifetime: 28326 hours (1180 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 fe 00 01 59 32 42 88 40 00 Error: UNC at LBA = 0x159324288 = 5791433352 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 90 00 00 96 13 93 f8 40 08 43d+14:39:23.093 READ FPDMA QUEUED 60 00 10 00 88 00 00 96 13 93 e8 40 08 43d+14:39:23.093 READ FPDMA QUEUED 60 00 50 00 80 00 01 5a a8 47 b0 40 08 43d+14:39:23.093 READ FPDMA QUEUED 60 03 a0 00 78 00 00 95 a2 e4 60 40 08 43d+14:39:23.093 READ FPDMA QUEUED 60 04 00 00 70 00 01 5a a8 43 b0 40 08 43d+14:39:23.093 READ FPDMA QUEUED Error 36 [11] occurred at disk power-on lifetime: 21424 hours (892 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 8d+20:21:44.666 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 8d+20:21:44.666 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 8d+20:21:44.665 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 8d+20:21:44.664 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 8d+20:21:44.664 SMART READ LOG Error 35 [10] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 0c c3 c8 88 40 00 Error: UNC at LBA = 0x10cc3c888 = 4509124744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 10 00 01 0c c3 c8 88 40 08 9d+17:47:05.168 READ FPDMA QUEUED 60 00 08 00 08 00 01 0c c3 c8 38 40 08 9d+17:46:57.677 READ FPDMA QUEUED 60 00 08 00 00 00 01 0c c3 c8 30 40 08 9d+17:46:57.677 READ FPDMA QUEUED 60 00 08 00 f0 00 01 0c c3 c8 28 40 08 9d+17:46:57.677 READ FPDMA QUEUED 60 00 08 00 e8 00 01 0c c3 c8 20 40 08 9d+17:46:57.676 READ FPDMA QUEUED Error 34 [9] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 0c c3 c8 00 40 00 Error: UNC at LBA = 0x10cc3c800 = 4509124608 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 c0 00 01 0c c3 c8 00 40 08 9d+17:46:53.852 READ FPDMA QUEUED 60 01 00 00 b8 00 01 3b 83 b5 d0 40 08 9d+17:46:53.813 READ FPDMA QUEUED 60 00 08 00 b0 00 01 3b 83 b4 d0 40 08 9d+17:46:53.812 READ FPDMA QUEUED 60 00 b8 00 a8 00 01 3b 83 b5 18 40 08 9d+17:46:53.812 READ FPDMA QUEUED 60 00 40 00 a0 00 01 3b 83 b4 d8 40 08 9d+17:46:53.811 READ FPDMA QUEUED Error 33 [8] occurred at disk power-on lifetime: 18269 hours (761 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5a 37 08 20 40 00 Error: UNC at LBA = 0x15a370820 = 5808523296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 38 00 01 5a 37 08 00 40 08 9d+17:35:43.838 READ FPDMA QUEUED 60 00 80 00 30 00 01 4c 43 d5 28 40 08 9d+17:35:41.921 READ FPDMA QUEUED 60 00 b8 00 28 00 01 5a 12 08 c8 40 08 9d+17:35:39.897 READ FPDMA QUEUED 60 00 08 00 20 00 01 5a 12 08 80 40 08 9d+17:35:39.897 READ FPDMA QUEUED 60 00 08 00 18 00 01 5a 12 08 48 40 08 9d+17:35:39.897 READ FPDMA QUEUED Error 32 [7] occurred at disk power-on lifetime: 18269 hours (761 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5a 12 08 40 40 00 Error: UNC at LBA = 0x15a120840 = 5806098496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d8 00 01 5a 12 08 78 40 08 9d+17:35:36.074 READ FPDMA QUEUED 60 00 08 00 d0 00 01 5a 12 08 70 40 08 9d+17:35:36.074 READ FPDMA QUEUED 60 00 08 00 c8 00 01 5a 12 08 68 40 08 9d+17:35:36.074 READ FPDMA QUEUED 60 00 08 00 c0 00 01 5a 12 08 60 40 08 9d+17:35:36.074 READ FPDMA QUEUED 60 00 08 00 b8 00 01 5a 12 08 58 40 08 9d+17:35:36.074 READ FPDMA QUEUED Error 31 [6] occurred at disk power-on lifetime: 18269 hours (761 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5a 12 08 18 40 00 Error: UNC at LBA = 0x15a120818 = 5806098456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 01 5a 12 08 38 40 08 9d+17:35:19.770 READ FPDMA QUEUED 60 00 08 00 50 00 01 5a 12 08 30 40 08 9d+17:35:19.770 READ FPDMA QUEUED 60 00 08 00 48 00 01 5a 12 08 28 40 08 9d+17:35:19.770 READ FPDMA QUEUED 60 00 08 00 40 00 01 5a 12 08 20 40 08 9d+17:35:19.770 READ FPDMA QUEUED 60 00 08 00 38 00 01 5a 12 08 18 40 08 9d+17:35:19.770 READ FPDMA QUEUED Error 30 [5] occurred at disk power-on lifetime: 18269 hours (761 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5a 12 08 17 40 00 Error: UNC at LBA = 0x15a120817 = 5806098455 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 18 00 01 5a 12 08 00 40 08 9d+17:35:12.753 READ FPDMA QUEUED 60 00 80 00 10 00 01 49 c1 89 08 40 08 9d+17:35:12.710 READ FPDMA QUEUED 60 01 00 00 08 00 01 5a 3d c9 80 40 08 9d+17:35:12.674 READ FPDMA QUEUED 60 00 08 00 00 00 01 5a 3d c8 80 40 08 9d+17:35:12.673 READ FPDMA QUEUED 60 00 b8 00 f0 00 01 5a 3d c8 c8 40 08 9d+17:35:12.673 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 46113 - # 2 Short offline Completed without error 00% 46089 - # 3 Short offline Completed without error 00% 46065 - # 4 Short offline Completed without error 00% 46041 - # 5 Short offline Completed without error 00% 46017 - # 6 Short offline Completed without error 00% 46017 - # 7 Short offline Completed without error 00% 45984 - # 8 Short offline Completed without error 00% 45960 - # 9 Short offline Completed without error 00% 45936 - #10 Short offline Completed without error 00% 45917 - #11 Short offline Completed without error 00% 45906 - #12 Short offline Completed without error 00% 45881 - #13 Short offline Completed without error 00% 45857 - #14 Short offline Completed without error 00% 45833 - #15 Short offline Completed without error 00% 45809 - #16 Short offline Completed without error 00% 45785 - #17 Short offline Completed without error 00% 45761 - #18 Short offline Completed without error 00% 45737 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 25/31 Celsius Lifetime Min/Max Temperature: 12/41 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (400) Index Estimated Time Temperature Celsius 401 2021-12-10 09:19 28 ********* ... ..( 66 skipped). .. ********* 468 2021-12-10 10:26 28 ********* 469 2021-12-10 10:27 27 ******** 470 2021-12-10 10:28 27 ******** 471 2021-12-10 10:29 26 ******* ... ..( 2 skipped). .. ******* 474 2021-12-10 10:32 26 ******* 475 2021-12-10 10:33 25 ****** ... ..( 15 skipped). .. ****** 13 2021-12-10 10:49 25 ****** 14 2021-12-10 10:50 26 ******* ... ..( 15 skipped). .. ******* 30 2021-12-10 11:06 26 ******* 31 2021-12-10 11:07 27 ******** ... ..(220 skipped). .. ******** 252 2021-12-10 14:48 27 ******** 253 2021-12-10 14:49 28 ********* ... ..(146 skipped). .. ********* 400 2021-12-10 17:16 28 ********* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 248005 Vendor specific === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 2 minutes for test to complete. Test will complete after Fri Dec 10 17:18:19 2021 Use smartctl -X to abort test.