smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.16.0-0.bpo.4-amd64] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: WD-WCC4N7TACJ0Z LU WWN Device Id: 5 0014ee 261f70f36 Firmware Version: 82.00A82 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Feb 18 17:31:18 2016 MST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 178 178 021 - 6083 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 714 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 12 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 981 194 Temperature_Celsius -O---K 128 119 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 8 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 8 [7] occurred at disk power-on lifetime: 714 hours (29 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 19d+06:59:38.309 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 19d+06:59:38.308 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 19d+06:59:38.308 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 19d+06:59:38.307 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 00 19d+06:59:38.307 SMART READ LOG Error 7 [6] occurred at disk power-on lifetime: 713 hours (29 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 19d+06:32:02.082 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 19d+06:32:02.082 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 19d+06:32:02.081 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 19d+06:32:02.081 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 00 19d+06:32:02.080 SMART READ LOG Error 6 [5] occurred at disk power-on lifetime: 712 hours (29 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 19d+05:37:40.020 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 19d+05:37:40.020 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 19d+05:37:40.019 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 19d+05:37:40.018 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 00 19d+05:37:40.017 SMART READ LOG Error 5 [4] occurred at disk power-on lifetime: 306 hours (12 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 2d+06:52:20.683 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 2d+06:52:20.682 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 2d+06:52:20.682 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 2d+06:52:20.681 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 00 2d+06:52:20.681 SMART READ LOG Error 4 [3] occurred at disk power-on lifetime: 305 hours (12 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 2d+06:29:41.577 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 2d+06:29:41.577 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 2d+06:29:41.576 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 2d+06:29:41.575 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 00 2d+06:29:41.575 SMART READ LOG Error 3 [2] occurred at disk power-on lifetime: 252 hours (10 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 01:01:43.799 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 01:01:43.799 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 01:01:43.798 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 01:01:43.797 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 00 01:01:43.796 SMART READ LOG Error 2 [1] occurred at disk power-on lifetime: 238 hours (9 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 01:38:20.331 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 01:38:20.331 SMART READ LOG 60 02 00 00 08 00 00 47 96 53 68 40 00 01:38:20.330 READ FPDMA QUEUED 60 02 00 00 00 00 00 47 96 51 68 40 00 01:38:20.330 READ FPDMA QUEUED b0 00 d6 00 01 00 00 00 c2 4f e0 00 00 01:38:20.329 SMART WRITE LOG Error 1 [0] occurred at disk power-on lifetime: 238 hours (9 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 01:33:09.561 SMART READ LOG 60 02 00 00 00 00 00 36 dc ec 00 40 00 01:33:09.560 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 01:33:09.560 CHECK POWER MODE b0 00 d5 00 01 00 00 00 c2 4f e1 00 00 01:33:09.560 SMART READ LOG 60 02 00 00 00 00 00 36 dc ea 00 40 00 01:33:09.559 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 624 - # 2 Short offline Completed without error 00% 456 - # 3 Extended offline Completed without error 00% 324 - # 4 Short offline Completed without error 00% 288 - # 5 Conveyance offline Completed without error 00% 252 - # 6 Short offline Completed without error 00% 251 - # 7 Short offline Completed without error 00% 69 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 20/25 Celsius Lifetime Min/Max Temperature: 20/31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (299) Index Estimated Time Temperature Celsius 300 2016-02-18 09:34 22 *** ... ..(476 skipped). .. *** 299 2016-02-18 17:31 22 *** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1666786 Vendor specific