smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.14.0-0.bpo.3-amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: WD-WCC4N6LR09AL LU WWN Device Id: 5 0014ee 2ba41a003 Firmware Version: 82.00A82 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Apr 5 11:16:18 2018 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40860) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 410) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 189 176 021 - 5525 4 Start_Stop_Count -O--CK 100 100 000 - 14 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 310 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 14 192 Power-Off_Retract_Count -O--CK 200 200 000 - 8 193 Load_Cycle_Count -O--CK 200 200 000 - 319 194 Temperature_Celsius -O---K 107 102 000 - 43 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 310 hours (12 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 5d+23:22:45.103 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 5d+23:22:45.103 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 5d+23:22:45.102 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 5d+23:22:45.101 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 5d+23:22:45.101 SMART READ LOG Error 8 [7] occurred at disk power-on lifetime: 270 hours (11 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 4d+06:47:13.526 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 4d+06:47:13.526 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 4d+06:47:13.525 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 4d+06:47:13.525 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 4d+06:47:13.525 SMART READ LOG Error 7 [6] occurred at disk power-on lifetime: 236 hours (9 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+20:57:38.969 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+20:57:38.969 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+20:57:38.968 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 2d+20:57:38.968 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 2d+20:57:38.968 SMART READ LOG Error 6 [5] occurred at disk power-on lifetime: 227 hours (9 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+11:46:03.533 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+11:46:03.533 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+11:46:03.532 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+11:46:03.531 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 2d+11:46:03.531 SMART READ LOG Error 5 [4] occurred at disk power-on lifetime: 221 hours (9 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+06:26:00.391 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+06:26:00.391 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+06:26:00.390 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+06:26:00.389 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 2d+06:26:00.389 SMART READ LOG Error 4 [3] occurred at disk power-on lifetime: 220 hours (9 days + 4 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+05:02:58.394 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+05:02:58.394 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+05:02:58.393 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+05:02:58.392 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 2d+05:02:58.391 SMART READ LOG Error 3 [2] occurred at disk power-on lifetime: 219 hours (9 days + 3 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+04:34:04.528 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 2d+04:34:04.528 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+04:34:04.527 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 2d+04:34:04.526 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 2d+04:34:04.526 SMART READ LOG Error 2 [1] occurred at disk power-on lifetime: 180 hours (7 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 12:53:36.502 SMART READ LOG b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 12:53:36.502 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 12:53:36.502 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 12:53:36.501 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 12:53:36.500 SMART WRITE LOG SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 221 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 40/48 Celsius Lifetime Min/Max Temperature: 20/48 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (21) Index Estimated Time Temperature Celsius 22 2018-04-05 03:19 42 *********************** ... ..(357 skipped). .. *********************** 380 2018-04-05 09:17 42 *********************** 381 2018-04-05 09:18 43 ************************ ... ..( 27 skipped). .. ************************ 409 2018-04-05 09:46 43 ************************ 410 2018-04-05 09:47 42 *********************** ... ..( 81 skipped). .. *********************** 14 2018-04-05 11:09 42 *********************** 15 2018-04-05 11:10 43 ************************ ... ..( 5 skipped). .. ************************ 21 2018-04-05 11:16 43 ************************ SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 14 --- Lifetime Power-On Resets 0x01 0x010 4 310 --- Power-on Hours 0x01 0x018 6 1250187412 --- Logical Sectors Written 0x01 0x020 6 905534 --- Number of Write Commands 0x01 0x028 6 12089239693 --- Logical Sectors Read 0x01 0x030 6 20338140 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 310 --- Spindle Motor Power-on Hours 0x03 0x010 4 59 --- Head Flying Hours 0x03 0x018 4 328 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 42 --- Current Temperature 0x05 0x010 1 41 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 44 --- Highest Average Short Term Temperature 0x05 0x038 1 28 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 44 --- Number of Hardware Resets 0x06 0x010 4 37 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 516223 Vendor specific