New user and new install

    • New user and new install

      Hello all,
      Long time FreeNAS user looking to switch to something more reliable and user friendly.
      I have a few questions:
      I have 32Gb of ram (4x8) should I reduce that down to 8 during the install to reduce the amount of swap Debian will automagically create?
      I have 6 x 1Tb 3.5 drives
      2 x 240gb ssd
      1 x 512gb nvme
      I have read that the os is not recommended on a USB drive, is the nvme drive over kill?
      The 6 1Tb + 2 ssd’s are on my hba card, will OMV boot from a hba?
      This is all for home storage plus mediaserver.
      What I plan to run is:
      Plex
      Sonarr
      Radarr
      Transmission
      Jackett
      Ombi
      Organizr
      Tautulli
      Pihole

      More specs
      Gigabyte MX31-BS0
      Intel(R) Xeon(R) CPU E3-1230 v5 @ 3.40GHz


      Sent from my iPhone using Tapatalk
    • Hey Savage,

      If you're installing on the NVMe I wouldn't worry about dropping the RAM down, but if it's not too hard pull out as much RAM as you can for the install.

      I actually just made a build today, I can't comment on the HBA's as I just use the motherboard SATAs (I don't really use RAID, I have 2x 3TB and 2x 2TB drives and I use Rsync to clone from one to the other each night as a backup - eventually the spare drives will move to a cheap QNAP laying around)

      I'd install OMV to the SSD, and then if you plan on running any VM's on your NAS (which I intend to as soon as I get the vbox plugin running) store your VMs on the nvme.

      youtube.com/watch?v=1pLKcT1tr_Y
      use this guide to split the drive after installing.

      NOTE: Use the flash memory plugin to protect the SSD. Also, don't store any crucial data on the nvme drive because you won't be able to recover it if it fails.
      ------
      Odin:
      Core i7-920
      22GB DDR3 RAM
      2x 3TB WD Drives, 2x 2TB Seagate Drives, 1x 1TB WD Drive, 1x 240gb Kingston A400 SSD
      OMV 4.1

      Minerva:
      QNAP TS-431
      (old NAS. coming back online soon as my backup solution)
    • New user and new install

      tkaiser wrote:

      SavageAUS wrote:

      Long time FreeNAS user looking to switch to something more reliable
      What lets you believe FreeNAS would be unreliable? If your issue is faulty hardware (e.g. using non-ECC RAM that throws bit flips) then your 'OMV experience' will be as unreliable as with any other NAS distro...


      Sorry forgot to mention I do have ECC memory.


      Sent from my iPhone using Tapatalk
    • New user and new install

      rayjaymor wrote:

      Hey Savage,

      If you're installing on the NVMe I wouldn't worry about dropping the RAM down, but if it's not too hard pull out as much RAM as you can for the install.

      I actually just made a build today, I can't comment on the HBA's as I just use the motherboard SATAs (I don't really use RAID, I have 2x 3TB and 2x 2TB drives and I use Rsync to clone from one to the other each night as a backup - eventually the spare drives will move to a cheap QNAP laying around)

      I'd install OMV to the SSD, and then if you plan on running any VM's on your NAS (which I intend to as soon as I get the vbox plugin running) store your VMs on the nvme.

      youtube.com/watch?v=1pLKcT1tr_Y
      use this guide to split the drive after installing.

      NOTE: Use the flash memory plugin to protect the SSD. Also, don't store any crucial data on the nvme drive because you won't be able to recover it if it fails.


      By installing OMV to the SSD I think you mean the NVMe? Then reuse the space on that drive for VM’s? I’ll mainly be using docker containers rather than VM’s.
      From my testing so far with my HBA card (IBM m1015 flashed to IT mode) I can install OMV to one of the SSD’s but not boot from it. So the two options I have left are the 512Gb NVMe (it’s a cheap adata one) or USB. If I choose to go the USB route plus the flash memory plugin would USB 3.0 be better? 16Gb or 32Gb? As I’ll buy a few to make clones. I do have easy access to the RAM so I’ll remove 3/4 sticks for install as I don’t think I’ll need that much swap? I could be wrong.


      Sent from my iPhone using Tapatalk
    • New user and new install

      rayjaymor wrote:

      Hey Savage,

      If you're installing on the NVMe I wouldn't worry about dropping the RAM down, but if it's not too hard pull out as much RAM as you can for the install.

      I actually just made a build today, I can't comment on the HBA's as I just use the motherboard SATAs (I don't really use RAID, I have 2x 3TB and 2x 2TB drives and I use Rsync to clone from one to the other each night as a backup - eventually the spare drives will move to a cheap QNAP laying around)

      I'd install OMV to the SSD, and then if you plan on running any VM's on your NAS (which I intend to as soon as I get the vbox plugin running) store your VMs on the nvme.

      youtube.com/watch?v=1pLKcT1tr_Y
      use this guide to split the drive after installing.

      NOTE: Use the flash memory plugin to protect the SSD. Also, don't store any crucial data on the nvme drive because you won't be able to recover it if it fails.


      By installing OMV to the SSD I think you mean the NVMe? Then reuse the space on that drive for VM’s? I’ll mainly be using docker containers rather than VM’s.
      From my testing so far with my HBA card (IBM m1015 flashed to IT mode) I can install OMV to one of the SSD’s but not boot from it. So the two options I have left are the 512Gb NVMe (it’s a cheap adata one) or USB. If I choose to go the USB route plus the flash memory plugin would USB 3.0 be better? 16Gb or 32Gb? As I’ll buy a few to make clones. I do have easy access to the RAM so I’ll remove 3/4 sticks for install as I don’t think I’ll need that much swap? I could be wrong.


      Sent from my iPhone using Tapatalk
    • SavageAUS wrote:

      From my testing so far with my HBA card (IBM m1015 flashed to IT mode) I can install OMV to one of the SSD’s but not boot from it. So the two options I have left are the 512Gb NVMe (it’s a cheap adata one) or USB. If I choose to go the USB route plus the flash memory plugin would USB 3.0 be better? 16Gb or 32Gb? As I’ll buy a few to make clones. I do have easy access to the RAM so I’ll remove 3/4 sticks for install as I don’t think I’ll need that much swap? I could be wrong.


      Sent from my iPhone using Tapatalk
      Just trying to give you other options --- to be honest using a 512gb NVMe is a shocking waste for OMV - so I'd partition it so I can find some use for the space, or even buy a really cheap M2 drive.

      (NVMe =/= M2 SSD...

      M2 = normal SSD with SATA3 speed on M2 connection
      NVMe = M2 connector but uses the PCIe channels for way more speed.)

      OMV runs perfectly fine on an 8gb or even 16gb USB3 drive - but I find it's a little more stable if you can use a SATA or M2 port as the USB drives are doomed to eventually fail.
      ------
      Odin:
      Core i7-920
      22GB DDR3 RAM
      2x 3TB WD Drives, 2x 2TB Seagate Drives, 1x 1TB WD Drive, 1x 240gb Kingston A400 SSD
      OMV 4.1

      Minerva:
      QNAP TS-431
      (old NAS. coming back online soon as my backup solution)
    • New user and new install

      rayjaymor wrote:

      SavageAUS wrote:

      From my testing so far with my HBA card (IBM m1015 flashed to IT mode) I can install OMV to one of the SSD’s but not boot from it. So the two options I have left are the 512Gb NVMe (it’s a cheap adata one) or USB. If I choose to go the USB route plus the flash memory plugin would USB 3.0 be better? 16Gb or 32Gb? As I’ll buy a few to make clones. I do have easy access to the RAM so I’ll remove 3/4 sticks for install as I don’t think I’ll need that much swap? I could be wrong.


      Sent from my iPhone using Tapatalk
      Just trying to give you other options --- to be honest using a 512gb NVMe is a shocking waste for OMV - so I'd partition it so I can find some use for the space, or even buy a really cheap M2 drive.

      (NVMe =/= M2 SSD...

      M2 = normal SSD with SATA3 speed on M2 connection
      NVMe = M2 connector but uses the PCIe channels for way more speed.)

      OMV runs perfectly fine on an 8gb or even 16gb USB3 drive - but I find it's a little more stable if you can use a SATA or M2 port as the USB drives are doomed to eventually fail.


      I appreciate the thoughts. I’ll look into a smaller m.2, I think I may have a 240GB m.2 drive somewhere, if I do I’ll use that for OMV.
      Next thing is should I use version 5 beta? Or stick with the latest 4. I see on the omvextras site they do not have 5 listed in the guides so I would be limited to what plugins etc. I could install to what comes with OMV.
      I’ve tried to install on a 8Gb USB 3.0 drive and it gave an error about partitioning even with only 8Gb ram in my machine.


      Sent from my iPhone using Tapatalk
    • New user and new install

      rayjaymor wrote:

      SavageAUS wrote:

      From my testing so far with my HBA card (IBM m1015 flashed to IT mode) I can install OMV to one of the SSD’s but not boot from it. So the two options I have left are the 512Gb NVMe (it’s a cheap adata one) or USB. If I choose to go the USB route plus the flash memory plugin would USB 3.0 be better? 16Gb or 32Gb? As I’ll buy a few to make clones. I do have easy access to the RAM so I’ll remove 3/4 sticks for install as I don’t think I’ll need that much swap? I could be wrong.


      Sent from my iPhone using Tapatalk
      Just trying to give you other options --- to be honest using a 512gb NVMe is a shocking waste for OMV - so I'd partition it so I can find some use for the space, or even buy a really cheap M2 drive.

      (NVMe =/= M2 SSD...

      M2 = normal SSD with SATA3 speed on M2 connection
      NVMe = M2 connector but uses the PCIe channels for way more speed.)

      OMV runs perfectly fine on an 8gb or even 16gb USB3 drive - but I find it's a little more stable if you can use a SATA or M2 port as the USB drives are doomed to eventually fail.


      I appreciate the thoughts. I’ll look into a smaller m.2, I think I may have a 240GB m.2 drive somewhere, if I do I’ll use that for OMV.
      Next thing is should I use version 5 beta? Or stick with the latest 4. I see on the omvextras site they do not have 5 listed in the guides so I would be limited to what plugins etc. I could install to what comes with OMV.
      I’ve tried to install on a 8Gb USB 3.0 drive and it gave an error about partitioning even with only 8Gb ram in my machine.

      Sorry for the double posts I’m not sure what’s happening.


      Sent from my iPhone using Tapatalk
    • New user and new install

      4 it is. And yes I have an intel 250Gb m.2 drive I’ll swap in for the os drive.
      On FreeNAS I was running ZFS raidZ2, the pool is already backed up and all 6 drives wiped ready for reinstall but is ZFS still the “best” option? Could I just go for raid6? And still have my 2 drives for parity/failure tolerance?


      Sent from my iPhone using Tapatalk