Beiträge von dani4gm

Ok. Got it.
I will check back if a new kernel (4.14?) will be implemented then I will try upgrading again, patch my OMV4 and see if My WD Red will be back.
Till then, I'll stay on OMV2 as it does the job nicely.

Have a good day!
Daniel

Hi Tkaiser,

Thanks for your quick reply.

Here is the output:
==================================

Linux Haspeu 4.13.0-0.bpo.1-amd64 #1 SMP Debian 4.13.13-1~bpo9+1 (2017-11-22) x86_64

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.

root@Haspeu:~# uname -a
Linux Haspeu 4.13.0-0.bpo.1-amd64 #1 SMP Debian 4.13.13-1~bpo9+1 (2017-11-22) x86_64 GNU/Linux
root@Haspeu:~# lsblk -a
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 2.7T 0 disk
ââsda1 8:1 0 2.7T 0 part
sdb 8:16 1 7.5G 0 disk
ââsdb1 8:17 1 5.5G 0 part /
ââsdb2 8:18 1 1K 0 part
ââsdb5 8:21 1 2G 0 part [SWAP]
root@Haspeu:~# blkid
/dev/sdb1: UUID="8eacee61-ba53-415c-bba3-e3f5c2690793" TYPE="ext4" PARTUUID="d0e792a8-01"
/dev/sdb5: UUID="2f1b59d1-6752-4ede-8912-b5d17d01c42a" TYPE="swap" PARTUUID="d0e792a8-05"
root@Haspeu:~# smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.13.0-0.bpo.1-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, http://www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD30EFRX-68AX9N0
Firmware Version: 80.00A80
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (39240) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 394) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 181 178 021 Pre-fail Always - 5916
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 586
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 712
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 470
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 43
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 542
194 Temperature_Celsius 0x0022 125 114 000 Old_age Always - 25
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0

SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 202 hours (8 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 00 00 00 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d5 01 e1 4f c2 00 08 01:04:18.163 SMART READ LOG
b0 d6 01 e0 4f c2 00 08 01:04:18.163 SMART WRITE LOG
b0 d6 01 e0 4f c2 00 08 01:04:18.161 SMART WRITE LOG
b0 d5 01 e0 4f c2 00 08 01:04:18.161 SMART READ LOG

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 203 -
# 2 Short offline Aborted by host 30% 203 -
# 3 Short offline Aborted by host 90% 203 -
# 4 Short offline Completed without error 00% 202 -
# 5 Short offline Aborted by host 90% 202 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@Haspeu:~#
============================================================

I am attaching a screenshot from OMV4 File System Menu, so you may see that sda1 is not visible, although it exists, so I am unable to mount it, using the GUI.

Thank you for your time!

Regards,
Daniel

Hello there,
I do need a helping hand / guidance.
I have a single 3TB drive with old data, XFS filesystem, and OMV4 on a USB stick (and another stick with OMV2).
Under OMV4, I am able to see the 3TB disk under Disks, as sda, BUT this is not visible/available under Filesystems, so I am unable to mount it. I am able to create, but this will wipe out my disk/data. If I plug another disk/usb drive, I am able to mount it under Filesystems, but sda is still invisible.
If I use OMV2, it's all ok, I am able to see/use the 3TB drive.
I should be able to use putty so, perhaps a magical mount command will fix my issue on OMV4, if anyone will be able to assist me with this, please.
I did a search in forum, with no luck. Additional data, I believe I formatted the drive with OMV1, xfs filesystem, 4 years ago.

Thanks in advance!
Daniel