yeah, it worked fine, thanks for help everyone
Beiträge von greenhorn92
-
-
Why not use a NAS?
Then you can connect any type of computer to the NAS, via the network, and share files between different computers via shares on the NAS. Very elegant and easy.
I intend my 4tb drive to be a part of the NAS. In fact, I even had everything set up, but as you can see in my earlier posts, I decided to switch to ext4. I need to move large quantity of data from my old drives to my NAS and the router is a heavy bottleneck, how much time would moving at least 1TB of data with 10MB/s speed take? While speed this low is still fine for moving small files as they appear or to stream some videos, I still need a way to access the file system directly.
I'll probably create some boot usb with ubuntu and transfer files from there I guess.
Edit: yeah, switched to EXT4 but the speed remains the same. Gotta get a new router soon.
-
Well, switching to ext4 is easy but finding a way to move files between windows 10 and ext4 is a goddamn hell... I have already spent hours dealing with creating sambashares on ubuntu and I begin to hate linux and its design focused on interrupting every possible user decision
-
Nah, there is only one router, it just had its name displayed this way (with a slash) which might have been confusing. I edited the main post.
Can you elaborate about the problems with Rpi4 and NTFS please? I know about potential performance degradation and that the transfer might be 10% slower on average but this doesn't sound too harsh tbh.
In any way, remaking the HDD to ext4 isn't that difficult but I'm not sure if there's a point in doing so
The second thing is that you seem to have ethernet traffic going via two different routers? That seems strange. And can be very bad. The LAN ethernet traffic should preferably not go via any router. Instead it should go via a separate GbE switch. Only traffic out/in should go via a router.
I'm not sure. The packets go to cable modem first, from there they go to the router which is connected via ethernet with the main PC and Rpi4. If I understand correctly, I don't have a separate GbE switch (the router acts as both switch and AP? IDK, I'm not really knowledgeable when it comes to networking)
-
I am currently using a following setup:
WD purple 4TB in an Icy Box IB-3620U3 connected to Rpi4 via USB3
TL-WR841N router connected through Ethernet to Rpi4 and my main PC and with WIFI with other network devicesPC: asuz z87-a motherboard (supposedly supports gigabit connection) with i5 4670k and WD blue HDDs
WD drive conencted to Rpi4 has has its contents shared to the other devices through sambashare. NTFS filesystem.
The issue is that the file transfer speed is around 10 MB/s. Considering that the router supports up to 300 Mb/s (both sides) then max transfer over wifi can be no higher than 18 MB/s - is that correct?
However, I expected the file transfer to be done via ethernet, which should yield higher speeds, no? Is my router the bottleneck here?
-
hey
i tried to follow the video found here but i cant access the web gui. I logged in through terminal, made new root password and rebooted. Logged back in via terminal, it says 161 updates are ready. However, I remain unable to access the web GUI. I think I waited more than 20 minutes for everything to load properly before I made any changes, is everything fine so far?edit: i managed to get to webgui after going through omv-firstaid configure web gui
edit2: at the point when i tried searching for plugin updates i arrived at the same errors as before pastebin
At this point i'm in a complete bind.
-
the message was too big for pastebin, i attach txt file with results
apt clean.txt
at this point it feels like i might as well start again from scratch for the third time -
used the command, rebooted, checked rdd files, they are fine.
the errors remain.
-
thank you for your fast reply. The NTP was enabled by default, but it had wrong timezone. I changed it, but I still get errors.
pastebin link -
Hello, I'm completely new to OMV (and arm in general)
I created an OMV instance on Rpi4. I managed to get into web GUI but when I tried to install docker I found out that it's not on the list. I decided to press check button and I got a huge list of errors:What is the meaning of it? It looks like some repositories are unavaiable for one reason or another but what about the other errrors? How should I approach fixing all this? I didn't expect a completely fresh install to have this many issues...
