I don't know much about this stuff, but these errors don't look good.... What do you think? Also, I had to delete some info as it wouldn't allow me to post more than 10,000 characters. I deleted what I thought was irrelevant.
Thanks so much for the help David.
Code
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 083 006 Pre-fail Always - 132114559
3 Spin_Up_Time 0x0003 100 092 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 314
5 Reallocated_Sector_Ct 0x0033 001 001 036 Pre-fail Always FAILING_NOW 4095
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 83792772
9 Power_On_Hours 0x0032 059 059 000 Old_age Always - 36360
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 221
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 095 095 000 Old_age Always - 5
188 Command_Timeout 0x0032 100 083 000 Old_age Always - 390848053341
189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 150
190 Airflow_Temperature_Cel 0x0022 053 036 045 Old_age Always In_the_past 47 (101 21 47 47)
194 Temperature_Celsius 0x0022 047 064 000 Old_age Always - 47 (0 12 0 0)
195 Hardware_ECC_Recovered 0x001a 051 021 000 Old_age Always - 132114559
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 249614909345285
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1105008341
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1405262392
SMART Error Log Version: 1
ATA Error Count: 28784 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 28784 occurred at disk power-on lifetime: 35107 hours (1462 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 09:28:29.808 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 09:28:29.747 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 09:28:29.747 NOP [Abort queued commands]
25 00 08 ff ff ff ef 00 09:28:29.747 READ DMA EXT
ef 03 46 00 00 00 a0 00 09:28:29.525 SET FEATURES [Set transfer mode]
Error 28783 occurred at disk power-on lifetime: 35107 hours (1462 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 09:28:29.525 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 09:28:29.464 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 09:28:29.464 NOP [Abort queued commands]
25 00 08 ff ff ff ef 00 09:28:29.464 READ DMA EXT
ef 03 46 00 00 00 a0 00 09:28:29.241 SET FEATURES [Set transfer mode]
Error 28782 occurred at disk power-on lifetime: 35107 hours (1462 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 09:28:29.525 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 09:28:29.464 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 09:28:29.464 NOP [Abort queued commands]
25 00 08 ff ff ff ef 00 09:28:29.464 READ DMA EXT
ef 03 46 00 00 00 a0 00 09:28:29.241 SET FEATURES [Set transfer mode]
Error 28781 occurred at disk power-on lifetime: 35107 hours (1462 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 09:28:29.241 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 09:28:29.181 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 09:28:29.181 NOP [Abort queued commands]
25 00 08 ff ff ff ef 00 09:28:29.181 READ DMA EXT
ef 03 46 00 00 00 a0 00 09:28:28.958 SET FEATURES [Set transfer mode]
Error 28780 occurred at disk power-on lifetime: 35107 hours (1462 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 09:28:29.241 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 09:28:29.181 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 09:28:29.181 NOP [Abort queued commands]
25 00 08 ff ff ff ef 00 09:28:29.181 READ DMA EXT
ef 03 46 00 00 00 a0 00 09:28:28.958 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Alles anzeigen