Beiträge von yous87uu2

resolved.

Zitat

route add -net 0.0.0.0 gw 192.168.1.1 netmask 0.0.0.0 dev wlan0

and work good.

Hi, i'm using OMV 1.5.
i'm use two different internet line, but one line is wlan.

before 1 years, i'm not using wlan line... but i want multiple network!

cause plug and setting usb wlan, wlan connect good.

see this.

Zitat

eth0 Link encap:Ethernet HWaddr 00:13:77:82:9c:66
inet addr:192.168.0.7 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:82626 errors:0 dropped:0 overruns:0 frame:0
TX packets:104460 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:41023835 (39.1 MiB) TX bytes:114087939 (108.8 MiB)
Interrupt:22 Base address:0xe000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:5728 errors:0 dropped:0 overruns:0 frame:0
TX packets:5728 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:914331 (892.9 KiB) TX bytes:914331 (892.9 KiB)

wlan0 Link encap:Ethernet HWaddr 00:26:66:04:d1:a9
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3842 errors:0 dropped:0 overruns:0 frame:0
TX packets:7964 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:429176 (419.1 KiB) TX bytes:9044625 (8.6 MiB)

Alles anzeigen

192.168.0.7 -> Existing Line. Nice work.
192.168.1.3 -> Wlan Line. only working in Local Network.

192.168.1.3 is cannot access in outdoor. 0.7 is work good.
192.168.1.3 is can connect only local network...

change DHCP to static, edit port-foward, Twin IP (use real ip. ex. router (real ip) -> PC (192.168.1.3) ==> router (real ip) -> PC (real ip) )... all not work!

i think, it's work on local network... cause maybe, server not allow added ip's Internet packet...?

---add route table

Zitat

Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
192.168.1.0 * 255.255.255.0 U 0 0 0 wlan0

Alles anzeigen

i'm using OMV 1.0.31 now.
somedays-a-go, i'm reset and remove my OMV 0.5, and format and install 1.0.
cause i'm setted like old config (by hand), any func is all good work, but Owncloud is dosen't work.

Server have 4 drives, cause i'm setted 4 shared folder. but owncloud just shown default files.
and create 'owncloud-(number)' in my 'FirstDrive' partiton (DATA partiton).

mount.json is look good. config.php too. i think.

how to fix this?

i'm attach some images.

Thanks.