I have several problems going on, the first is OMV doesn't always show up in file explorer, sometimes I can refresh file explorer and it'll work, sometimes I have to reset my server and it'll show up. The second problem is I have a Samsung blu-ray player which will usually detect the server, but when I got to it and pick the movie folder or tv folder, it will just give me the loading icon, and will not do anything else. I have gotten it to work, the other day I put several movies on it and tv shows, and I watched a full season of Game of Thrones with no problem. I get on there today and it keeps freezing up, and when it does work, the new movies I've added to it don't show up, even though I can go to file explorer and see them in the Plex folder. Any suggestions would be helpful, but after all the trouble this thing has given me, a replacement in software might be the best way to go.
Beiträge von Chad88
-
-
-
-
-
You're right I wasn't using the client. I have that installed now, but no matter what username I use I get,
Status: TLS connection established.
Command: USER chad
Response: 331 Password required for chad
Command: PASS *********
Response: 530 Login incorrect.
Error: Critical error: Could not connect to server -
-
I'll stop looking at it, for the passive ftp, is the ranges 49150-49155 good? I seen tekebebe had a thread about it, and he used 14100 I believe.
Ok, I will try that. I'll have to read up on it, as I just used ssh for the first time last week. I'm a bit of a noob when it comes to this stuff.
When I use filezilla, do I just type in Ftp: ip address where I would normally type the ddns? I did that with the browser earlier and it still does the same thing, I type in my credentials and it'll just loop. It does this with all the users I created.
It say's port 21 is open.
-
Ok, so I have it working again. I disabled NAPT, I also noticed in the guide the guy added port forwarding for 443 which I didn't do at first. So I'm guessing it was that or disabling NAPT that worked. However, now when I try to log in with the browser it opens up the host I assigned wit no-ip, but after I put in my credentials, it flashes and those spaces go blank. I can not get past this stage now. I also can not log in through filezilla.
-
I will make sure NAPT is disabled later. Looks like I have another problem now, I rebooted my router and openmediavault, and now when it boots up, all I see is a black screen with a flashing cursor in the top left corner. So after I figure this out, I'll get back to the port forwarding issue.
-
I used a port checker, it keeps saying the port is closed. I can use the web interface and ssh into it. I have a motorola surfboard modem in front of my router. I have the surfboards wireless turned off, but I noticed it has port forwarding as well. Do I need to change any of the port forwarding or ddns settings on it as well, or just on my router?
-
I have that set up, I currently only have one user set up, but I allowed all privileges. I don't know if this is the problem, but when i set up ddns on my router, I don't remember exactly what it said, but it didn't say anything was wrong. Now on my router, when I go to ddns and click show status, it says "their is no ip address on the internet port". Could this be the problem?
-
-
Yes, but I've never set it up before. The way I did it was, after I gave my server a static ip, I went to port forwarding on the router and gave the server a starting port of 21 and ending port 22. I set the passive ports to 49150 and 49155. I read some other places that said just use 21 which I changed it on the router and it didn't help at all.
-
Hello everyone, I'm completely new to this. I've worked with linux before a little, but this is my first server, my first time setting up a domain. I have gotten to the point where I can see my media vault under network, and all the folders. I followed this guide http://en.jose-crispim.pt/arti…_openmediavault.html#p2_4. The only thing I did different from that guide is, my router doesn't have a "enable NAT" box to select. I set up a host on noip.com, after downloading the update client and realizing I had to check the "edit hosts" box and check my host, I was able to log on once. I entered my username and password, the following page didn't show any of my folders. So I exited the page, and the gui for router which I had open. I didn't change anything, but I can not log back on. It says webpage not available. I'm doing this through my browser, I haven't been able to log on using filezilla. Any advice would be helpful, as I said I'm completely new to this.