I see the graph but the Temp Values are:
0.5 Min 7.93 Avg 18.30 Max 6.20 Last
The values are to small?!
Can you post the output of the following 3 commands
Your hardware is being detected but its using a temp from another sensor and not the CPU.
I see the graph but the Temp Values are:
0.5 Min 7.93 Avg 18.30 Max 6.20 Last
The values are to small?!
Can you post the output of the following 3 commands
Your hardware is being detected but its using a temp from another sensor and not the CPU.
sensors:
radeon-pci-0008
Adapter: PCI adapter
temp1: +9.0°C (crit = +120.0°C, hyst = +90.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +15.0°C (high = +70.0°C)
(crit = +70.0°C, hyst = +69.0°C)
________________________
ls /var/lib/rrdcached/db/localhost/sensors-*/:
/var/lib/rrdcached/db/localhost/sensors-k10temp-pci-00c3/:
temperature-temp1.rrd
/var/lib/rrdcached/db/localhost/sensors-radeon-pci-0008/:
temperature-temp1.rrd
________________________
cat /proc/cpuinfo:
processor : 0
vendor_id : AuthenticAMD
cpu family : 21
model : 19
model name : AMD A4-4000 APU with Radeon(tm) HD Graphics
stepping : 1
microcode : 0x6001119
cpu MHz : 1400.000
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
apicid : 16
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce tbm topoext perfctr_core perfctr_nb arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1
bogomips : 5989.14
TLB size : 1536 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 48 bits physical, 48 bits virtual
power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro
processor : 1
vendor_id : AuthenticAMD
cpu family : 21
model : 19
model name : AMD A4-4000 APU with Radeon(tm) HD Graphics
stepping : 1
microcode : 0x6001119
cpu MHz : 3000.000
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 1
apicid : 17
initial apicid : 1
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce tbm topoext perfctr_core perfctr_nb arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1
bogomips : 5989.14
TLB size : 1536 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 48 bits physical, 48 bits virtual
power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro
It does look like its detecting the right sensor, the only way to be sure is to do cat /usr/share/openmediavault/mkconf/collectd.d/sensors and if you see lines like ${DATA}/sensors-k10temp-pci-00c3/temperature-temp1.rrd it is working ok
It does look like its detecting the right sensor, the only way to be sure is to do cat /usr/share/openmediavault/mkconf/collectd.d/sensors and if you see lines like ${DATA}/sensors-k10temp-pci-00c3/temperature-temp1.rrd it is working ok
This is one line from output
DEF:cpuc0avg=\${DATA}/sensors-k10temp-pci-00c3/temperature-temp1.rrd:value:AVERAGE \
i take a look in the UEFI there a Temps ~ 40-50°C
temp1: +15.0°C
I looks like your sensors report temps above 40, so when you look at the graphs you need to think of the value +40
i use the version is 3.3.2 Date 2012
is it possible to update to 3.3.5?
its the current version. and work the graph with this version?
i get this message (run sensors-detect):
Driver `w83627ehf':
* ISA bus, address 0x290
Chip `Nuvoton NCT6776F Super IO Sensors' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
w83627ehf
#----cut here----
add this to modules?
You could try modprobe w83627ehf first as adding it to modules can cause problems, run lm-sensors after. If any thing goes wrong run rmmod w83627ehf
sorry, misread the post
Now i see the fan speed etc, but the CPU Temp is the same.
In etc/sensors3.conf is nothing for k10temp only k8temp.
That looks very good! Thank you!
i will check the bios CPU-temp later.
Tried installing 1.0.3 just now (on Kralizec 1.8), but when activating CPU temp and then hitting save I get this;
Error #2002:
exception 'OMVException' with message 'Invalid method parameter: buttonvalues-inputEl does not exist, and it is not an optional property.' in /usr/share/php/openmediavault/rpcservice.inc:187
Stack trace:
#0 /usr/share/openmediavault/engined/rpc/sensors.inc(122): OMVRpcServiceAbstract->validateMethodParams(Array, '{\n ...')
#1 [internal function]: OMVRpcServiceSensors->setSettings(Array, Array)
#2 /usr/share/php/openmediavault/rpcservice.inc(125): call_user_func_array(Array, Array)
#3 /usr/share/php/openmediavault/rpc.inc(79): OMVRpcServiceAbstract->callMethod('setSettings', Array, Array)
#4 /usr/sbin/omv-engined(500): OMVRpc::exec('Sensors', 'setSettings', Array, Array, 1)
#5 {main}
Any suggestions?
Reminder to myself: https://github.com/OpenMediaVa…rs/openmediavault-sensors
PS: This should really be included in core along with the other graphs, just imagine on a busy media server doing much transcoding. Would be nice to keep an eye on thoes temps
Same issue here
When the new field was added to all plugins the code on git hub was not working and unfortunately this broken version was released.
I will fix this by the weekend.
thx jhmiller
When the new field was added to all plugins the code on git hub was not working and unfortunately this broken version was released.
I will fix this by the weekend.
Any news on this? Very eager to try it out
Got a little side tracked, found issue and fixed it locally but still need to test it before committing. I also tried to correct the colour chooser menu but go nowhere so might squash that for now.
Give me a couple of more days, I will post back here when done.
Hi, where is the latest version of this plugin? I have downloaded one version that installs but then give me errors when I try to display the plugin in the tree.
Any help?
I had wanted to fix the coloUr menu drop box but was unable to
I will revert back to hard coded coloUrs.
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!