Snapraid data error in aquota.user

The typical Snapraid install using the plugin excludes those files, among others, by default.

Quote from Sean

I installed it using the plugin, but I recently had an error during an update of the plugin, maybe something went wrong there.

Edit: below is my snapraid.conf. The only excluded files are snapraid.conf*

Does it make sense to edit it manually, or will the changes be overwritten by the next update? I haven't seen any way to add excludes from the frontend.

Make sure you have the current version of the plugin which is 3.7.7.

Look in /etc/default/openmediavault-snapraid these are the default excludes. If you don't have this file reinstall the plugin.

If you make manual changes to snapriad.conf they will be lost the nest time you use the plugin to make any changes.

To use the plugin to add excludes and includes, see the Rules tab.

i have almost the same problem

my conf:

xclude *.unrecoverable

exclude lost+found/

exclude aquota.user

exclude aquota.group

exclude /tmp/

exclude .content

exclude *.bak

exclude /snapraid.conf*

yet i get:

Data error in file '/srv/dev-disk-by-uuid-7d46260d-a71f-4138-8ab1-8ae5bac8e8d6/a quota.group' at position '0', diff bits 59/128

Data error in file '/srv/dev-disk-by-uuid-7d46260d-a71f-4138-8ab1-8ae5bac8e8d6/a quota.user' at position '0', diff bits 71/128

on another omv with the same setup there are no errors

in both cases the rule section in the plugin are empty

so my head have a hard time understading why 2 equal setups behave different... and only on 1 of 5 disk in the system with the problem

both omv's are updated to latest version

these defaults are in the config section of the plugin thou... so i assume they are in effect in both cass?

i added the excludes in the rules section, now they are there doubble in the config section

will do a full force sync and see if the errors are there or not, will take a VERY loooooong time

Quote from boelle

i added the excludes in the rules section, now they are there doubble in the config section

will do a full force sync and see if the errors are there or not, will take a VERY loooooong time

There are default excludes already in place. If you add the same ones yourself, you will get errors.

Try running snapraid status instead of snapraid sync.

root@bo-omv:~# snapraid status

Self test...

Loading state from /srv/dev-disk-by-uuid-2e4e0ef5-a94a-4973-9ca2-acf2c23f1d24/snapraid.content...

Using 224 MiB of memory for the file-system.

SnapRAID status report:

Files Fragmented Excess Wasted Used Free Use Name

Files Fragments GB GB GB

7956 1 15 - 215 275 44% sdb1_disk1

22042 62 192 505.8 1722 1708 50% sdc1_disk2

757 5 49 - 137 176 43% sdd1_disk3

2509 21 63 - 861 1106 43% sde1_disk4

--------------------------------------------------------------------------

33264 89 319 505.8 2937 3266 47%

84%|o

|*

|*

|*

|*

|*

|*

42%|*

|*

|*

|*

|*

|*

|* o

0%|*________________________________________o__________________________oo

1 days ago of the last scrub/sync 0

The oldest block was scrubbed 1 days ago, the median 1, the newest 0.

WARNING! The array is NOT fully synced.

You have a sync in progress at 99%.

The 16% of the array is not scrubbed.

No file has a zero sub-second timestamp.

No rehash is in progress or needed.

No error detected.

doing another full sync while i have dinner etc