Temperature CPU?

It worked for me, but after reinstallation of OMV 2 the Graphs don't apear...

Zitat von Niemand

It worked for me, but after reinstallation of OMV 2 the Graphs don't apear...

Did you re-install sensors? did you refresh the page after selecting your monitors?

i reinstalled it for 3 times and refreshed the page for 5 times and even rebootet for 2 times. It doesn't work.

Have you cleared browser cache?

Do the tabs show with unhappy faces or no tabs at all?

No tabs for me either,tried Chrome and IE. Cleared cache, etc...

same here. Before reinstalling of OMV it worked...

Zitat von Niemand

same here. Before reinstalling of OMV it worked...

Reinstalling or upgrading?

Could you both try running/usr/sbin/omv-mkgraph

If it does not change anything try running the sh -x ...... command I posted a couple of pages back (posting on phone so can't link to it) PM me the output.

Zitat von jhmiller

The raspberry pi has no built in sensors, from what I have seen you would need to get/build an addon module that can get CPU temp.

Isn´t it be possible to get the temperature by vcgencmd measure_temp? Then it should be possible to just get the temp by a simple SED or AWK command.

Zitat von jhmiller

Reinstalling or upgrading?

Could you both try running/usr/sbin/omv-mkgraph

If it does not change anything try running the sh -x ...... command I posted a couple of pages back (posting on phone so can't link to it) PM me the output.

I'll tell you the whole story:

With 1.16 (or something like that) it worked. Updated to 1.18 it worked, updated to 1.19 it didn't work. upgraded to 2.1 it worked. Because of the issue with no-HDD-spindown i reinstalled 2.1 and it don't work.
When I'm home I try to do what you asked for.

The main file for tabs is /var/www/openmediavault/js/omv/module/admin/diagnostic/system/plugin/Sensors.js
This file has the tabs for each sensor chosen on the plugin page, if you have no tabs showing then there might be an issue with the creation of this file. Check if it is made and what is inside it.

Another user has said the /var/lib/rrdcached/db/localhost/ has no folders starting with sensors- check if this is the case with you also.

Zitat von WastlJ

Isn´t it be possible to get the temperature by vcgencmd measure_temp? Then it should be possible to just get the temp by a simple SED or AWK command.

ATM I just want to use the data from lm-sensors, later on and if that method works then we could look at implementing it.

I do not have the Sensors.js file. but I do have a folder /var/lib/rrdcached/db/localhost/sensors-coretemp-isa-0000 with the files temperature-temp2.rrd temperature-temp3.rrd temperature-temp4.rrd temperature-temp5.rrd in it.

Would like to check the output of sh -x /usr/share/openmediavault/mkconf/sensors to try and see why the file is not created.

Output is here: http://pastebin.com/QEd5pYVj

Just enable CPU temp only and try again, you have enabled sensors for things you do not have so instead of throwing an error it is just not creating any graphs.

@mikebetz42 & @Niemand

New version (1.0.17) released that I hope will fix your issues. After upgrading/installing make sure you change something so that new settings can be applied and remember to refresh the page before checking graphs.

Gigabyte EP45-UD3P - Tab is there but unhappy pictures for graphs. (no fans selected)

ASUSTeK P8B75-M - Working (no fans selected)

Both are OMV 2.1.5.1 - the EP45-UD3P is also giving me the Headphones issue... link for Headphones in the GUI does not work, etc. I may have some other issue going on but this one is running a lot more plugins than the other install. Everything else is working, so not sure what I have going on.

After some tinkering I was able to get the EP45-UD3P to show:

~# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +47.0°C  (high = +82.0°C, crit = +100.0°C)
Core 1:       +46.0°C  (high = +82.0°C, crit = +100.0°C)
Core 2:       +42.0°C  (high = +82.0°C, crit = +100.0°C)
Core 3:       +44.0°C  (high = +82.0°C, crit = +100.0°C)


it8718-isa-0290
Adapter: ISA adapter
in0:          +1.12 V  (min =  +0.00 V, max =  +4.08 V)
in1:          +2.10 V  (min =  +0.00 V, max =  +4.08 V)
in2:          +3.28 V  (min =  +0.00 V, max =  +4.08 V)
+5V:          +2.98 V  (min =  +0.00 V, max =  +4.08 V)
in4:          +0.46 V  (min =  +0.00 V, max =  +4.08 V)
in5:          +0.06 V  (min =  +0.00 V, max =  +4.08 V)
in6:          +0.10 V  (min =  +0.00 V, max =  +4.08 V)
in7:          +3.10 V  (min =  +0.00 V, max =  +4.08 V)
Vbat:         +3.26 V
fan1:        1776 RPM  (min =   10 RPM)
fan2:           0 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
fan4:           0 RPM  (min =    0 RPM)
temp1:        +39.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp2:        +38.0°C  (low  = +127.0°C, high = +80.0°C)  sensor = thermal diode
temp3:         -2.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
intrusion0:  ALARM

I have the all of the tabs now, but no graphs...

After installing the nct6775 driver for the P8B75-M I now have:

# sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:        +27.8°C  (crit = +106.0°C)
temp2:        +29.8°C  (crit = +106.0°C)


coretemp-isa-0000
Adapter: ISA adapter
Physical id 0:  +36.0°C  (high = +85.0°C, crit = +105.0°C)
Core 0:         +36.0°C  (high = +85.0°C, crit = +105.0°C)
Core 1:         +35.0°C  (high = +85.0°C, crit = +105.0°C)


nct6779-isa-0290
Adapter: ISA adapter
in0:                    +0.83 V  (min =  +0.00 V, max =  +1.74 V)
in1:                    +1.03 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in2:                    +3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in3:                    +3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in4:                    +1.00 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:                    +2.04 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:                    +1.58 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in7:                    +3.46 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in8:                    +3.38 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in9:                    +1.06 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in10:                   +0.31 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in11:                   +0.18 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in12:                   +1.00 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in13:                   +1.03 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in14:                   +0.22 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:                     0 RPM  (min =    0 RPM)
fan2:                  1190 RPM  (min =    0 RPM)
fan3:                     0 RPM  (min =    0 RPM)
SYSTIN:                 +32.0°C  (high =  +0.0°C, hyst =  +0.0°C)  ALARM  sensor = thermistor
CPUTIN:                 +34.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
AUXTIN0:                +27.0°C    sensor = thermistor
AUXTIN1:                +77.0°C    sensor = thermistor
AUXTIN2:               +111.0°C    sensor = thermistor
AUXTIN3:                +12.0°C    sensor = thermal diode
PECI Agent 0:           +28.0°C
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C
PCH_CHIP_TEMP:           +0.0°C
PCH_CPU_TEMP:            +0.0°C
intrusion0:            ALARM
intrusion1:            ALARM
beep_enable:           disabled

@mikebetz42
The Sensors.js file is being created so that issue is fixed, now its why the graphs are blank.
Are you running 1.0.17?
If so, give the output of sh -x /usr/share/openmediavault/mkconf/sensors again.

Where created, give the contents of these files

/usr/share/openmediavault/mkconf/collectd.d/sensors
/usr/share/openmediavault/mkconf/collectd.d/mb
/usr/share/openmediavault/mkconf/collectd.d/fan
/usr/share/openmediavault/mkconf/collectd.d/sys

>Are you running 1.0.17?
Yes

EP45-UD3P: http://pastebin.com/P6P7QjA6

ASUS P8B75-M: http://pastebin.com/YEQkP9b8

Source Code
/usr/share/openmediavault/mkconf/collectd.d/sensors
/usr/share/openmediavault/mkconf/collectd.d/mb
/usr/share/openmediavault/mkconf/collectd.d/fan
/usr/share/openmediavault/mkconf/collectd.d/sys

Looks like you found the issue none of these files are on Gigabyte EP45-UD3P

Only sensors exists and has information on the ASUS P8B75-M and the CPU temps are working.