Does it still show when you run sensors
Run sh -x /usr/share/openmediavault/mkconf/sensors and give me the results, remember to only enable the CPU temp.
Does it still show when you run sensors
Run sh -x /usr/share/openmediavault/mkconf/sensors and give me the results, remember to only enable the CPU temp.
# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +37.0°C (high = +105.0°C, crit = +105.0°C)
Core 1: +37.0°C (high = +105.0°C, crit = +105.0°C)
it8772-isa-0a30
Adapter: ISA adapter
in0: +0.73 V (min = +2.62 V, max = +2.95 V) ALARM
in1: +1.37 V (min = +1.66 V, max = +1.12 V) ALARM
in2: +2.00 V (min = +2.89 V, max = +0.37 V) ALARM
+3.3V: +3.34 V (min = +4.20 V, max = +4.92 V) ALARM
in4: +2.02 V (min = +1.45 V, max = +3.02 V)
in5: +2.02 V (min = +2.62 V, max = +1.12 V) ALARM
in6: +2.22 V (min = +0.38 V, max = +1.62 V) ALARM
3VSB: +3.31 V (min = +5.71 V, max = +3.31 V) ALARM
Vbat: +3.24 V
fan1: 0 RPM (min = 10 RPM) ALARM
fan2: 0 RPM (min = 11 RPM) ALARM
fan3: 336 RPM (min = 94 RPM)
temp1: +28.0°C (low = -50.0°C, high = +57.0°C) sensor = thermal diode
temp2: +25.0°C (low = -67.0°C, high = -51.0°C) ALARM sensor = thermal diode
temp3: -128.0°C (low = -87.0°C, high = +0.0°C) ALARM sensor = disabled
intrusion0: ALARM
Alles anzeigen
and
the attachment for sh -x /usr/share/openmediavault/mkconf/sensors
rm /usr/share/openmediavault/mkconf/sensors
wget -O /usr/share/openmediavault/mkconf/sensors https://raw.githubusercontent.com/OpenMediaVault-Plugin-Developers/openmediavault-sensors/master/usr/share/openmediavault/mkconf/sensors
chmod +x /usr/share/openmediavault/mkconf/sensors
/usr/share/openmediavault/mkconf/sensors
Update the script again, refresh the webui and then check graphs.
If it still does not work can you check if /var/lib/rrdcached/db/localhost/ has a folder called something like sensors-it877....
If it does have the folder can you re-run the debug command again, making sure you have enabled CPU temp.
Thanks
Sorry, but no graphs again....
# ls -al /var/lib/rrdcached/db/localhost/
totale 0
drwxr-xr-x 11 root root 220 ott 27 21:53 .
drwxr-xr-x 3 root root 60 ott 25 02:05 ..
drwxr-xr-x 2 root root 200 ott 25 02:05 cpu-0
drwxr-xr-x 2 root root 200 ott 25 02:05 cpu-1
drwxr-xr-x 2 root root 100 ott 25 02:05 df-root
drwxr-xr-x 2 root root 100 ott 27 21:53 df-srv-dev-disk-by-label-ServerXPDoc
drwxr-xr-x 2 root root 100 ott 25 02:05 interface-eth0
drwxr-xr-x 2 root root 60 ott 25 02:05 load
drwxr-xr-x 2 root root 120 ott 25 02:05 memory
drwxr-xr-x 2 root root 220 ott 25 02:05 rrdcached
drwxr-xr-x 2 root root 80 ott 27 21:19 sensors-coretemp-isa-0000
Alles anzeigen
I don't have the folder you tell me....
Hi,
I tried also to disable coretemp module and refresh sensors with /usr/share/openmediavault/mkconf/sensors but nothing changed in my sad graphics...
Have you new ideas?
Thankyou for assistance.
Helped me.
1. add in /etc/default/grub
GRUB_CMDLINE_LINUX="acpi_enforce_resources=lax"
2. in shell
update-grub2
3. add in /etc/modules
it87
I follow alexicon's instructions but this is the output:
root@ServerOMV:/var/lib/rrdcached/db/localhost# ls -al
totale 0
drwxr-xr-x 11 root root 220 ott 27 21:53 .
drwxr-xr-x 3 root root 60 ott 25 02:05 ..
drwxr-xr-x 2 root root 200 ott 25 02:05 cpu-0
drwxr-xr-x 2 root root 200 ott 25 02:05 cpu-1
drwxr-xr-x 2 root root 100 ott 25 02:05 df-root
drwxr-xr-x 2 root root 100 ott 27 21:53 df-srv-dev-disk-by-label-ServerXPDoc
drwxr-xr-x 2 root root 100 ott 25 02:05 interface-eth0
drwxr-xr-x 2 root root 60 ott 25 02:05 load
drwxr-xr-x 2 root root 120 ott 25 02:05 memory
drwxr-xr-x 2 root root 220 ott 25 02:05 rrdcached
drwxr-xr-x 2 root root 80 ott 27 21:19 sensors-coretemp-isa-0000
Alles anzeigen
Of course I relunch commands to regenerate sensors conf... so there isn't the folder.
What is acpi_enforce_resources=lax? I see in internet that may be dangerous for the hardware. Is it safe?
Thankyou
There are plans to make a plug-in for OMV 4?
The plugin works under OMV 4. I had it installed when i upgraded and it's working fine.
I installed the plugin on the OMV 4.0.15-1 and switching-on in the Services -> Sensors CPU Temperature, Show Cores and MB Temperature. There were graphs in Diagnostics -> System Informaton -> Performance statistics -> OMV Sensors. But these graphics are not updated, but stand still. The Refresh button does not help. The graphs are updated only if I make the switching-off / switching-on and Save Apply in the Services -> CPU Temperature or Show Cores or MB Temperature or all off/on. The remaining graphics in Performance statistics are updated normally.
Hi,
I've recently tested the plugin on a NanoPi Neo2 and it seems that this CPU temperature sensor is not supported yet.
Would it be possible to support a CPU with just 1 temperature sensor?
Regards,
Timeless
I try to use the plugin on 2 omv machinesfo testing.
Both are running with the 3.16.0-5-amd64.
My issue on the first one ist that only the cpu teperature is showing as a graph all other are "empty".
root@test-nas-01:~# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +42.0°C (high = +78.0°C, crit = +100.0°C)
Core 1: +39.0°C (high = +78.0°C, crit = +100.0°C)
it8721-isa-0a10
Adapter: ISA adapter
in0: +2.22 V (min = +1.03 V, max = +2.28 V)
in1: +2.22 V (min = +2.75 V, max = +0.92 V) ALARM
in2: +2.22 V (min = +2.94 V, max = +0.64 V) ALARM
+3.3V: +3.36 V (min = +6.07 V, max = +5.33 V) ALARM
in4: +2.22 V (min = +2.99 V, max = +1.13 V) ALARM
in5: +2.22 V (min = +2.82 V, max = +2.69 V) ALARM
in6: +2.22 V (min = +2.10 V, max = +0.66 V) ALARM
3VSB: +3.29 V (min = +5.09 V, max = +4.15 V) ALARM
Vbat: +3.24 V
fan1: 809 RPM (min = 55 RPM)
fan2: 912 RPM (min = 13 RPM)
fan3: 0 RPM (min = 33 RPM) ALARM
temp1: +22.0°C (low = -17.0°C, high = -3.0°C) ALARM sensor = thermal diode
temp2: -128.0°C (low = +57.0°C, high = -68.0°C) sensor = Intel PECI
temp3: +22.0°C (low = +70.0°C, high = -66.0°C) ALARM sensor = Intel P ECI
intrusion0: OK
Alles anzeigen
any ideas ?
Tom
The plugin works under OMV 4. I had it installed when i upgraded and it's working fine.
But what if you have a fresh install of OMV 4? It is not listed in the plugins list, how can I install it?
But what if you have a fresh install of OMV 4? It is not listed in the plugins list, how can I install it?
You can't.
There is no version compatible with OMV4, and I doubt very much there ever will be, sorry.
Any news for OMV4 ? Almost middle of 2019 is here..
Any news for OMV4 ? Almost middle of 2019 is here..
Nope. No one is working on it.
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!